nexus 5 wireless charger with case 3d models
2987305 3d models found related to nexus 5 wireless charger with case.thingiverse
This is a dock for the Nexus 5. The dimensions are setup for a N5 with a Spigen Neo Hybrid (75mm side to side for phone). I haven't left any space for a conventional charger... sorry. The hole thing is about 100mm x 100mm x 100mm. ...
thingiverse
Customized version of http://www.thingiverse.com/thing:1663499 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1663499 Instructions Using the following options:...
pinshape
Qi Wireless charger for nexus 5. Electrical components purchased from amazon: http://www.amazon.ca/dp/B011TTU0T6/ref=pe_386430_1... ... Uses 4 cylindrical permanent magnets with diameter and length of a 1/4 inch
thingiverse
... Charger. ... For Nexus 5 Android Smartphone. Compatible with Smart Technology Super Mini Qi Wireless Charger. ... Instructions This model has hanging part (bottom of charger) so needs support, use your favourite software to generate support for it.
youmagine
A holder that fits the wireless charger and a Nexus 5. ...It is intended to make locating the phone on the charger simpler, and to lift the phone up for a better viewing angle.The design has been done in OpenSCAD.There may be some more developments...
thingiverse
Nexus 5 wireless charger stand. This design was modified slightly from the one done by adamj12b, but I couldn't figure out how to upload my design to his page, so I've added it to mine. The main differences are as follows: it is scaled up by 1% as...
thingiverse
A table stand for Nexus 4 and Nexus 5 with mount for a cheap Wireless Charger. There are outlets for the speakers/microphone. Nexus 4 on the back, Nexus 5 on the Bottom. Printed well with 0.2mm layer and 15% infill in 3.5 hours To be printed without...
thingiverse
A table stand for Nexus 4 and Nexus 5 with mount for a cheap Wireless Charger. There are outlets for the speakers/microphone. Nexus 4 on the back, Nexus 5 on the Bottom. A slightly optimized version of my first one:...
prusaprinters
Holder for Nexus 5 with Wireless Qi Power Charger Pad http://www.amazon.co.uk/dp/B00FEAGVWM with and wihtout flipcase. better stability of the Nexus 5 in the holder by rounded bottom better stability ot the stand by lower position of the device ...
thingiverse
Holder for Nexus 5 with Wireless Qi Power Charger Padhttp://www.amazon.co.uk/dp/B00FEAGVWM with and wihtout flipcase. better stability of the Nexus 5 in the holder by rounded bottom better stability ot the stand by lower position of the device...
thingiverse
I wanted to practice on some fancy lofts so this is what I came up with. The source files are in SolidWorks 2013-14. ... Instructions Two components required but you need three parts.
thingiverse
This is a dock I designed for my nexus 5 and a cheap wireless QI charger I got from DX.com. http://dx.com/p/t1501-qi-standard-mobile-wireless-power-charger-black-269927#.UxkxyPnSBvA The QI charging pad fits flush into a cutout. The two legs are...
thingiverse
I picked up a couple of cheap QI wireless charger coils and circuit boards on ebay for about 10 bucks ( http://www.ebay.com/itm/291111266809 ) And printed this little stand for my Google Nexus 5. I haven't tested the electronics cover, but it...
grabcad
This is wireless charging stand for my Nexus 5. Installed in Skoda Yeti. For fixing the stand I use slits between radio and panel and blower and panel. The distance between the plates is adjustable, so it must work also for other cars. Additionally I...
thingiverse
This is a fixture for using a nexus wireless charger as a dash mount for my Nexus 5 phone. It is printed in two pieces which are fastened together using a screw (a little glue is also helpful). The ball socket works with many standard dash mounts...
thingiverse
The electronics for wireless charger is this one: http://www.ebay.com/itm/131626000948?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT Print Settings Printer Brand: RepRap Printer: Prusa i3 Rafts: No Supports: Yes Resolution: 0,2mm Infill:...
prusaprinters
This is a fixture for using a nexus wireless charger as a dash mount for my Nexus 5 phone. It is printed in two pieces which are fastened together using a screw (a little glue is also helpful). The ball socket works with many standard dash mounts...
thingiverse
CD mounted Universal/Nexus 5 holder with QI wireless charger Download actual phone holder from http://www.thingiverse.com/thing:370228
thingiverse
This works for both the Nexus 4 and 5, I tried to make it parametric so it could be used for other devices as well but can't test. This uses the "Metrans Mwt03" charger (amazon link), any of the small puck QI chargers should work. ... Sources ...
thingiverse
A buddy had a problem with his nexus sliding off this charger because of how steep the angle was, so I made this for him. The angle is adjustable and much flatter. ... He said it's working very well for him.
thingiverse
The Google Nexus 5 wireless charger is great, but it must be aligned properly with the phone for charging to occur. I built this after several times waking up to a dead phone. The caddy holds the charger and the phone in proper alignment so...
thingiverse
This wireless charger fits the Qi charging circuit available from Adafruit Industries (https://www.adafruit.com/products/2162) and is sized for a Nexus 5 and 4 and should work for other phones that support wireless charging as well. The charging...
thingiverse
A wireless charging stand I designed for my Nexus 5 & 7 devices. It is designed to work specifically with the CHOETECH Qi Wireless Charging Pad, available from Amazon The charging pad fits snugly into the recessed slot and includes a strain relief...
thingiverse
Did you have a nexus 5 with a nexus wireless charger and now you have a nexus 6 which doesn't quite work with the old wirelss charger? Then this is the model for you. This model uses the qi charger for a nexus 5...
thingiverse
With my nexus 5 I've bought the genuine Nexus wireless charger adapter, which has its upper part made by glass. As I'm very lucky it felt from my hands and hit the ground breaking the glass. So I thought: "What about printing a new glas?" Here is...
thingiverse
Customized version of http://www.thingiverse.com/thing:1655546 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1655546
thingiverse
Customized version of http://www.thingiverse.com/thing:526257 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=526257