nylock mod prusa mk3s 3d models

You will need the screws to mount, and if not using a case, a nut to hold the screws on the other side. The bracket is a remix from articulating camera arm listed below, but there's no reason why you couldn't use it by itself to just hold a Pi for...

Attach vertical LED lights to your Prusa Mk3/MK3s easily with this LED kit. The Lights run vertically up the sides to help eliminate shadows and clearly light up the printing area. ...A switch is used to turn the lights on and off. BOM: 2x -...

The filament sensor lever on the Prusa MK3S is prone to falsely reading that filament is present even when it's not. The design intent of the sensor is to have this lever move in front of the IR sensor when filament is present and when filament runs...

The bearings are specifically for ColorFabb 750 gram spools and also for the spools shipped by Prusa with their printers (which I believe are all 750 gram silver PLA spools). The tolerances on the bearings are pretty tight (+/-0.15mm), so make sure...

The bearings are suitable for ColorFabb 750 gram spools and for the spools shipped by Prusa with their printers, which I believe are all 750 gram silver PLA spools. The tolerances on the bearings are pretty tight (±0.15mm), so ensure that your...

This spool holder is a 90 degree rotated version of the Original Prusa MK3S+ Prusament 2 kg spool holder redesigned from scratch, based on the original holder dimensions. I cannot guarantee that this will not break or do some damage to your printer,...

Also added a new extruder cover with zip-lock for camera wire. Upgraded my Prusa MK3 extruder to MK3S version and the old nozzle camera mount can't be used behind the printing head any more. So tinkering a bit with camera placement, found the left...

This is a dial indicator holder that can be quick and easily mounted onto the Prusa MK3s extruder and is rigid enough for precise measurements. It uses my Universal tool carrier plate to interface with the extruder body. (The tool carrier plate is...

They are softer and provide better noise reduction than just using the grey feet. Print Settings Printer Brand: Prusa Printer: I3 MK3S Supports: Yes Resolution: 0.3 Infill: 10% Filament: eSun TPU Notes: Printing bottom fillet is always hard with...

The bearings are for ColorFabb 750 gram spools and for the spools that Prusa ships with their printers (I believe these are all 750 gram silver PLA spools). The tolerances on the bearings are pretty tight (±0.15mm), so make sure that your printer is...

These bearings are specifically tailored for use with 750-gram ColorFabb spools and the silver PLA spools shipped by Prusa with their printers (all of which I believe weigh in at 750 grams). The tolerances on these custom bearings are incredibly...

This is a Customized Timelapse Clock Holder for Prusa I3 MK3S. It securely attaches to the X axis. The button design is credited to Stebo : https://www.thingiverse.com/thing:1570116 # Print Settings 1 x TimelapseClockHolder1 : Layer thickness set at...

Das Display kann zum Arbeiten abgenommen werden und danach wieder eingesteckt werden. Print Settings Printer Brand: Prusa Printer: I3 MK3S</div>Rafts: No Supports: No</div>Resolution: 0,15mm Infill: 15%</div> Filament: Extrudr...

This is a custom-built Camera Holder for Prusa I3 MK3S. It's secured firmly in place along the X axis. This design is a modified version of "Raspberry Camera Holder for Geeetech A10" available on Thingiverse...

This means you maintain the full 210mm Z height, instead of other BMG designs which make you lose 5 -10mm.Simple Mosquito (or Magnum) Hotend mounting without an adapter or groove mount that allows it to be installed and removed completely without...

The mount can then be fixed to the tripod. Remixed models The motor mount is derived from https://www.prusaprinters.org/prints/3991-logitech-c270-mount-prusa-i3-mk3. The tripod mount is derived from https://www.thingiverse.com/thing:2501430 Print...

The screen on the mk3s is too bright, I cannot find any moving lid for the screen so I design mine.

Mounting to micrometer clock, for help in getting a flat bed when making the Nylock adjustment.I find this mount more accurate than others I have tried. ...You can recreate the same measurement every time even if you move around the extruder, which...

This cover is supposed to block out any dust or particles that are trying to enter the extruder of your i3 MK3s+ printer during the times when there is no filament loaded.I always take my filament of the machine when I am not printing anything, to...

Alles weitere erfahrt ihr hier: https://forum.prusaprinters.org/forum/original-prusa-i3-mk3-benutzermodifikationen-octoprint-gehaeuse-duesen/mk3s-sinterbronzelager-y-achse/#_ga=2.40195234.1458135807.1636729801-1603073617.1619737348Viel Erfolg...

Same as the original card, I suggest default settings with:0.15mm layer height0.4mm nozzleThese “gift card” models make great gifts, but what if you intend to assemble it right away? Why 3D print the card and sprue to immediately cut it off? Uses 64%...

I wanted a sturdy webcam mount for my prusa MK3s and decided to make this one. The design is parametric, you can adjust the angle, length and height of arm which allows control of the exact position of the webcam in 3D space (just be careful to make...

https://youtu.be/TISsHycrOuQ   Inspired by David Roy's kinetic sculptures I made this rotation indicator for my Prusa MK3S. The spirals turn in different directions thanks to a planetary gear. I designed everything so it would all be held together...

Hello,\r\n\r\nThis is an updated wire guide for the latest MK3s printers that can accommodate a bowden fit M6x1mm.\r\nThere are two versions available. The first version retains the original dimensions, while the second offers increased chamfers and...

V3 Now available redesigned Bigger and Better!https://www.prusaprinters.org/prints/127748-prusa-mk3s-ultimate-toolbox-v3-bigger-and-better~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~This is my...

Core components can be purchased from our website https://www.hall-precision.com/product-page/modular-3d-printer-enclosure-prusa-mk3sPlease print the latest versions (highest v#) for best results.STL FilesAll .stl files are correctly oriented for...

PLA or PETG. If you use my LCD side mount mod this clip holder is a must: https://www.thingiverse.com/thing:3483560 But this functional Z=axis brace actually improves your prints and therefore is a requirement:...

New instructions can be found here: https://jltxplore.dozuki.com/c/Skelestruder_for_Prusa_MK3. I've moved these to their permanent home, but let me know if you see any issues with the transfer. Motivation: I wanted to see if I could create a...

Honestly, it would be nice if Prusa would just ship the i3 MK3S+ this way. It makes the printer far more reliable. Since I swapped these in, I have only had one jam. and that was from a bad loading on my part.The Z-axis cap comes from Prusa, but so...

I'm adapting codiac2600's concept to match the specifications of an MK3S, and I'm currently conducting tests to assess whether this modification results in any noticeable improvements.