nzxt h510 hard drive bay 3d models
96549 3d models found related to nzxt h510 hard drive bay.thingiverse
This is for a video. ...https://youtu.be/NaTBuYsSpjU Made for NZXT H510
thingiverse
Casefanholder 120mm for extra Fans on the bottom of your NZXT H510 Elite Case
thingiverse
shorter feet for the NZXT H510. may also fit H500 but can't confirm it. "ohne" version with flat bottom and one with indented bottom Print with support. ...(x/y dist ~0.8mm)
thingiverse
This is/was a project of mine to keep drives that I'm doing data recovery on cool while they are running. ... It uses a 92mm PC fan to blow across the drives in hopes of keeping them cool enough to run data recoveries.
cults3d
This is/was a project of mine to keep drives that I'm doing data recovery on cool while they are running. ... It uses a 92mm PC fan to blow across the drives in hopes of keeping them cool enough to run data recoveries.
thingiverse
One of my H510's foot was broken so i remade it in a stronger version on the parts that broke. ... You need to keep the screw and the rubber pad that was installed with the old one, you can just glue it on the 3D print.
thingiverse
This is a wall mount for NZXT H510 Elite, but I think it will fit other NZXT cases to. ...Mount is 215 mm wide.
thingiverse
This a remix of the hard drive bay (https://www.thingiverse.com/thing:276524) where one can access all the holes unlike the original one.
myminifactory
It was designed for my specific setup but it should be able to fit into many rigs with minor adjustments to the height and foot, although I would recommend it particularly for use with the NZXT H510 Elite as the case has a cable managing bracket the...
thingiverse
... on eBay for 20$) and a 140mm fan in the back panel to cool the drives. ... To make the full assembly, you will need: 4x tray cage mirror -mid 4x tray cage -mid 16x drive tray At some point, I will make a spacer to allow the use of 2.5-inch drives. ...
thingiverse
Anti vibration mount for the NZXT H510 case. If you don't have these special screws that are shown in the pictures than print the files with the name _small_screw however I did not test those. the ending _46 and _35 refer to the diameter of the...
thingiverse
Use this to fit a 3.5" hard drive into a half-height (5.25" optical drive) bay. I used dimensions from the following two standards: 3.5" disk drive: SFF-8301: ftp://ftp.seagate.com/pub/sff/SFF-8301.PDF5.25" optical drive SFF-8851:...
pinshape
SummaryUse this to fit a 3.5" hard drive into a half-height (5.25" optical drive) bay. I used dimensions from the following two standards: 3.5" disk drive: SFF-8301: ftp://ftp.seagate.com/pub/sff/SFF-8301.PDF 5.25" optical drive SFF-8851:...
thingiverse
Allows you to put the Vive connector box in an empty drive bay on a NZXT Switch case. The adapter is not perfect and I would probably do it differently if I were to redo it. It may work in other computers but I can't guarantee it will. ... Idea...
thingiverse
It was missing the hard drive bay cover and I figured I'd try to measure the gap with my calipers and print one. This works quite well. You may try elongating the little tab to make it more secure, but it works as-is. ... I'm going to deliver the...
thingiverse
The reason for creating this is because I noticed that the NZXT H510 Elite has terrible airflow. I created this spacer to open the front panel slightly enough to increase airflow and not disturbed the aesthetic of a closed glass case. ...Enjoy.
thingiverse
Wanted something to hold my hard drives for my Open NAS. Its not pretty, but functional. Print with fan grill on the build plate, no supports required. Would love to know how to fix the "Object may not be a valid 2-mainfold" error. STL...
thingiverse
I bought a used AeroCool StrikeX open air case and it was missing one of the sliding hard drive mounts. I created this one to be as close to the original as I could make it with my printing capabilities at the time. As with all my items, it is...
thingiverse
My GPU was suffocating inside my H510 Elite, so I created a front and side panel for better airflow. ...Air filters coming soon.
thingiverse
Here is a expansion box that is created for adding 3 more hard drives internal in a computer case. Printed best with a 1- 1.6mm shell 100% infill is needed for good solid cage. ...also ABS or Nylon is best as the drives could warp PLA if you don't have...
prusaprinters
<p>I designed this model to fit in a HP Z240 full tower chassis. ...This will probably only work in computers with tool-less drive installation that is similar to the HP design.
thingiverse
just a mount designed with 3080ti for the NZXT H510
thingiverse
For the inside pieces I used 2 walls, 0 bottom and top layers 30% cubic subdivision for the pattern (pick whatever you like) I did the hole with the grinder and its dimensions are 160x300mm
cults3d
a support for my vertically mounted Gigabyte RTX 3080 OC, which is mounted using a cooler master V2 universal vertical GPU bracket, the holes slot into the base of the case like lego.
thingiverse
a support for my vertically mounted Gigabyte RTX 3080 OC, which is mounted using a cooler master V2 universal vertical GPU bracket, the holes slot into the base of the case like lego.
thingiverse
Headphone holder for NZXT H510 Elite housing. Trial and error is not for the professional model. ... 15-30% filling for PLA can be used.