octoprint raspi camera 3d models
113219 3d models found related to octoprint raspi camera.cults3d
Made the case for your 3D Printer octoprint on raspberi pi 3 b + 2020 profile Stabilizer step-down 5A XL 4015 1pcs https://ru.aliexpress.com/item/1PCS-5A-DC-DC-adjustable-step-down-module-XL4005-NEW/32326880194.html PC cooler 30X30X10 5V 2pcs...
thingiverse
Made the case for your 3D Printer octoprint on raspberi pi 3 b + 2020 profile Stabilizer step-down 5A XL 4015 1pcs https://ru.aliexpress.com/item/1PCS-5A-DC-DC-adjustable-step-down-module-XL4005-NEW/32326880194.html PC cooler 30X30X10 5V 2pcs...
thingiverse
octoprint raspi case with fan and dual relays for alfawise u30
thingiverse
This thing is based upon vinnievg's raspi case, and barneyj's ball joint. ... I hope this works for you!
thingiverse
Minimal Raspi ZeroW frame, Anycubic V-Slot clip(just shortened Goldex' version) and a simple connection bay in case theres nothing around. ... split for easier printing Frame holes are 21mm for M2 screws EDIT: added frame for m2.5 screws (26mm)
prusaprinters
This is a raspi zero camera housing with wall / floor mount and ball pivot. it is made for the small camera modules. do not use the sticky tape on the camera flex foil, everything fits snugly. do not melt the pins inside the holes of the raspi. the...
thingiverse
This is a remix to fit my [32x32mm RasPi camera](https://www.amazon.com/gp/product/B09DCQRZF4/). ... You will need to print the mount arm from the original thing, here:...
thingiverse
This is a simple camera holder for the raspberry Pi camera and CR-10 printer. ... No support necessary.
youmagine
be careful not to dislodge the yellow block under the camera lens - the next iteration of this will have more space here :)You can now hotglue the lens from the glasses over the camera lens and the camera head should then bolt through to the top of...
thingiverse
I had more or less everything lieing around, so I decided to design this enclosure for the IR LEDs, the raspi and the NoIR cam and built it. It is still not perfect, but everything sits fine and works like a charm. Information on the parts I used...
pinshape
These magnets can be obtained from Element 14: http://au.element14.com/duratool/d01766/magnets-rare-earth-8-x-3mm-pk10/dp/1888095 Finally, an optional 5mm LED can be installed in the lower hole of the camera to allow increased Infrared illumination...
thingiverse
A camera platform for the RasPi camera. Only the platform needs some support for the “teeth”. Created using Fusion 360, with thanks. For the camera case. I have used the following: thing:1646474 https://www.thingiverse.com/thing:1646474 Update: I...
thingiverse
Support for installing a camera on the 3d printer for use with octoprint.
thingiverse
Simple but functional Ender 3 support for a raspberry pi camera connected to Octoprint
thingiverse
RasPi camera mount for the TEVO Tornado. mounts next to the y-axis limit switch. ...print 2 connector pieces.
thingiverse
This camera holder pretends to position the Octoprint camera (which you can find on any online shop) above your computer screen. ... This stand enables 3 degrees of freedom.
thingiverse
octoprint pi IR camera mount for knock-off weewooday cameras. ... I use the articulating arm from one thing and remixed another to create this.
thingiverse
This is a camera mount for a Raspi camera which can be mounted on a tripod. I have provided light threads on the holder to mount on a tripod. There is also a slot for the ribbon cable to go thru, to connect to the Raspi connector. ... The circular cut...
thingiverse
... cable version. In that case, it will be enough with 16cm version. In [this post](http://apuntes.eduardofilo.es/2018/10/20/Octoprint-en-Anet-A8.html) (in spanish I'm afraid) there is instructions for installing a Raspberry with Octoprint in Anet A8.
thingiverse
... them one. To attach this assembly to the printer, remove the right front corner heat bead spacer and put the camera assembly where the spacer was. ... https://www.amazon.com/gp/product/B013JTY8WY/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
thingiverse
Remix of the reinforced RasPi camera arm (only) by Jerware to include three magnets to mount on an enclosure. ...I used these magnets with a drop of superglue, with three to match on the other side:...
thingiverse
... ready to print files later on after I get it printed. Wishing my raspi camera could go wireless, but still crazy excited to get this printed! This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/4h0WHdb6dnW
thingiverse
This is a segmented arm for mounting an octoprint camera on a 3-d printer. It requires a c-clamp (Gimiton C-Clamp Camera Mount Clamp Clip Aluminum Heavy Duty C Clamp U Clip Bracket for Photo Studio Light Stand Camera Flash). I purchased the c-clamp...
cults3d
Another Raspberry Pi Anet A8 camera mount. I designed this for my Octoprint server. The camera housing is a remix and is not designed by myself. The housing seems to be a copy of a copy of a copy....(found on Tinkercad) So I can't pay tribute to the...
thingiverse
Another Raspberry Pi Anet A8 camera mount. I designed this for my Octoprint server. The camera housing is a remix and is not designed by myself. The housing seems to be a copy of a copy of a copy....(found on Tinkercad) So I can't pay tribute to the...
thingiverse
... integriertem LCD für Temperatur, Luftfeuchtigkeit, Prozessorauslastung etc., Fernein-/abschaltung des 3D-Druckers über Octoprint Interface. ... mehr unter http://cool-web.de/raspberry/octoprint-raspi-zero-status-lcd-mit-dht11-und-433-mhz-steuerung.htm
thingiverse
Perfect fit for Raspberry Camera V1.3. The Mounting bracket fits with two M3X12 screws as shown on the pictures..I have also included 18mm slot for easy cable management. ... walls 5 top layer 4 bottom layer 4 infill 20
thingiverse
Snap together camera case for Raspberry Pi 4 with HQ Camera Module
thingiverse
cable clip for raspberry pi camera. ... Suitable for Ender 3 (Pro) and maybe other printers with x-profile frame.