odroid h2 3d models

The ODROID-H2 attaches to the bottom section via screws before the top casing is lowered onto it. The bottom part then secures to the top case using additional screws. It's engineered with M.2 SSD compatibility in mind for the ODROID-H2. ... Photos of...

... for reference, the ram connector is 10mm high and 73mm wide. Here are the drawings I used to make this model. https://wiki.odroid.com/_media/odroid-h2/odroid_h2_top.png?cache= https://wiki.odroid.com/_media/odroid-h2/odroid_h2_rear.png?cache=

This is a small form factor case for the Odroid H2+. The top is cut out for heatsink clearance, and there are mounts for optional 25mm fans for active cooling. ...The case assembles with 14 M2.5 x 6 bolts and hex nuts, and the Odroid board is mounted...

For secure attachment of the Odroid-H2, M3x30 screws and nuts are used, and screw sizes can also be adjusted according to your preferences. The case has precise dimensions of 13 x 12 x 6.5 cm when configured with a 9.5 mm 2.5" disk. For this...

Odroid H2 Blade Rack ================ This is my design for a blade rack to host Odroid h2 units: https://www.hardkernel.com/shop/odroid-h2/. The rack is 4U high, with about 1cm of space above and below each bay for airflow. Each bay features a 40mm...

https://www.hardkernel.com/shop/odroid-h2/ This design mounts 2 x 2.5 drives below mainboard keeping clearance for ram and nvme drive. The design allows for simple protection on my typically crowded desktop. The pc board is supported off desktop and...

The SATA power cables were custom made, from a stock Molex to SATA power cable cut down to 10cm and re-terminated with the four-pin 2.54mm pitch JST XT connectors which the Odroid H2 has on board. ... ## Source Source FreeCAD models:...

[https://www.hardkernel.com/shop/odroid-h2/] This design mounts 2 x 2.5 drives below mainboard keeping clearance for ram and nvme drive. The design allows for simple protection on my (typically crowded) desktop. The pc board is supported off desktop...

This is my design of a blade rack for Odroid h2 https://www.hardkernel.com/shop/odroid-h2/. It is 4U high including about 1cm above and below for airflow, each bay has a 40mm fan, I used...

This is a simple and compact case for the Odroid H2 and hopefully updated to be compatible with the H3 (untested since I don't have one).The case is in two parts and there are two variants of each half. The bottom can support two 2.5" HDDs or come in...

This is a case I made for the Odroid H2+ "single board" computer. If you don't know what that is, it's an tiny (110mm x 100mm) X86 computer with a J4115 Intel Celeron processor. The specs don't look like much on paper, but it's surprisingly...

I use Odroid Rackmount upright and in the 2nd evolution step as baseplate to connect 60mm Noctua fans on each Odroid H2 / H3. (1st evolution step is viewable in the background of one picture with 80mm Noctua fans, but they outgrow the hight of one...

The ODROID-H2 Modular Case is a four-part masterpiece. It consists of a top section, a main body, a disk holder, and a bottom panel - all expertly crafted to be easily printed without the need for complex supports. This innovative design allows you...

ODROID H2 PLUS/H2 CASE Case, slim light fast to print and has a 19mm front on button. m3 screws required 40mm smaller ones for pcb 10mm works fine. ...

## Required Items: - [Odroid H2](https://www.hardkernel.com/shop/odroid-h2/) - Sata & power cable - 92mm slim fan - 70mm fan - PWM fan splitter - Case feet - M3x10 female-to-female standoff - Phillips Flat Head Countersunk Bolts ## To-Do List: -...

... using these specs. For more information and guidance, check out the forum thread at https://forum.odroid.com/viewtopic.php?f=172&t=35309, where enthusiasts have shared their own experiences and tutorials on creating a NAS system with the ODROID-H2.

Partial body: use 2B1-2B5 ## Items Needed (non-exhaustive list): - [Odroid H2](https://www.hardkernel.com/shop/odroid-h2/) - [LCD](https://www.hardkernel.com/shop/i2c-lcd-module/) - [HDD thumb screw](https://www.google.com/search?&q=6-32+thumb+screw)...

ODROID-H2 Modular Case for Hardkernel 4 modular parts (Top, Main, Disk, Bottom) are included for easy assembly with no supports needed. The design allows for 0, 1, or 2 disk modules to be added as desired. M3 screws secure the components in place.

This is a case i designed for Odroid H2+ to use in conjunction with the Sinden Arcade light guns. this case is held together with feet bands that are printed and the SBC is screwed in with thing small plaster screws this case is awesome for any...

Odroid H2 2 3.5"HDD NAS Designed in Fusion 360, All panels printed with ABS, side panels should be something stiffer like aluminum. HDD mounts are printed with TPU For structural rigidity, side panels should be made with alu panels. ... Parts...

Odroid-H2+ to mini-ITX adapter including 2.5" SSD adapter. Probably works with non-plus as well. Created this due to clearance issues with existing designs and plus version. YMMV, please triple check all clearances etc. Be especially careful with...

The Odroid H2 and the Odroid H2+ are some of the few single board computers which offer PC like interfaces including 2x SATA, an NVMe slot, 2x 2.5 GBit ethernet (1 GBit for the H2) as well as dual RAM sockets. Besides the interfaces the board is...

This is remix of a Case for a NAS Build with the Odroid H2/2+/3/3+ BoardsI added new HDD rails with vibration dampening.The rails consist of two partsthe rail shell is of PLA/PETGthe rail inserts are TPUThere are two different railslong railshortend...

The Odroid-H2 Case is a versatile and modular design that allows users to easily upgrade or add storage capacity as needed. To take full advantage of this feature, a 3.5" HDD Slide-In Module has been designed specifically for this case. This module...

A bracket to hold a M.2 to SATA-Adapter in place. Other M.2 modules of the format xx42 may also fit. However, if not the same module is used make sure there is 2.5mm free space on the PCB from the edge where the bracket grabs the module. ...Otherwise...

Modified the great H2 modular case by myang777 to fit the new H3. Adjusted cutouts on the top plate to suit the slightly larger heatsink and repositioned headers. Unfortunately, there is now very little space between the heatsink and the...

These are labels for the Odroid H2 blade server enclosure bays. ... To learn more, visit https://www.thingiverse.com/thing:2755897

Odroid H2 to Mini-ITX Adapter Following a conversation on the Odroid forum, several innovative ideas emerged for housing the new Odroid H2 motherboard. This model presents one idea using an adapter to connect between a mini-ITX motherboard and the...