olympus om10 battery cover 3d models
200543 3d models found related to olympus om10 battery cover.myminifactory
This is an eye cup for my 1979 Olympus OM10 camera. I recently started printing in TPU and found that this was the perfect thing to design and print. ... I designed it with a small radius around most edges to give it a nice look.
thingiverse
This is a battery cover for Olympus BLS-50. It is designed with Design Spark Mechanical 4.0. I printed with Elegoo MARS UV 3D printer with default parameter with NOVA3D UV 405nm transparent resin. ...
thingiverse
This is a battery cover for the Olympus BLN-1 Battery cover. It is made to exactly fit with as less play as possile. Optimal print quality with .5 mm wall thickness and .4 mm solid infill (100%). Recommended to print with PLA and heated bed, but...
thingiverse
Battery cover for BLS-1 batteries. ... Print Settings Printer: Afinibot A5 Mini Rafts: Doesn't Matter ...
thingiverse
This is a case for Olympus BLS50 batteries. It has one hole from each side with the discription of full and empty. ... Each battery have one little triangle ,that i paint it with a marker, and you have to place it in the right side of the case to...
thingiverse
This is a battery adapter for an Olympus e500 DSLR camera. Used to replace the battery and power the camera with a 7.2V DC adapter. Use at your own risk. This may permanently damage your camera. I am not responsible for any damages Post-Printing You...
thingiverse
https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...
thingiverse
Click on top cover for an Olympus BLN-1 type battery. Created in Solidworks. ... Be gentle guys, it's my first design...
thingiverse
A spare part for the olympus om-d e-m10 mark ii and iii
thingiverse
There are two versions, one is just a cover, the other one has some holes to allow passing some wire to use the battery on arduino and so projects. I own three BLM-1 batteries so, I can confirm it fits perfectly with this battery. I guess it works...
thingiverse
I needed a clean way to store and organize my Olympus OMD EM-5 batteries, this does a great job at that. ...
thingiverse
... to be printed with color change. ...If your battery is empty, simply flip the lid to indicate charge status. Depending on printer settings and callibration, the lid may need reduce thickness a little. ... Made for Olympus BLS-5, BLS-50, PS-BLS1
thingiverse
This is another remix of gernesha's battery cap, this time for the Olympus BLS-5 battery. It is my understanding that the BLS-1, BLS-5, and BLS-50 batteries are the same size and therefore should fit this battery holder as well. These are used in a...
prusaprinters
Olympus BLH-1 battery case. Tight fit around the battery.Has an indicator hole so you can indicate whether it's charged.Slightly smaller than the original clear plastic caseMuch easier to useNo thin plastic flexy clamp arms. ...Uses a couple of...
thingiverse
This is a battery holder for Olympus BLH-1 batterys. I found the idea here for Canon LP-E6 batteries and took my own aproach to this. UPDATE: 30.01 Did my first Print (which failed for other reasons) and made some adjustment according to my...
thingiverse
This battery magazine holds three OMD EM10 Mark VI batteries
thingiverse
For Olympus BH2 UMA. ... The two side covers are easy to lost. You can make a iron cover as replacement.
prusaprinters
This is a pretty basic case for up to 3 LI-92b batteries. This lid snaps into place with the indents. The case is square, so the lid fits in any orientation. I printed with PLA with 0.2mm layers and 15% infill. Probably could do less infill as there...
thingiverse
**Lens cover for the Olympus PEN-F analog camera.** Modelled after the original metal cap. It can be printed in two ways: 0. The "F" facing up - depending on your printer, supports may be required 0. ...Cut the model in half at around 5mm, with the...
thingiverse
This is a lens cover for the Olympus TG series of cameras. I have a TG-5 but understand that it will fit most earlier versions in the series. It has been specifically designed with caving in mind. The cover in the closed position protects the...
prusaprinters
Lens cover for the Olympus PEN-F analog camera. Modelled after the original metal cap. It can be printed in two ways: The "F" facing up - depending on your printer, supports may be required Cut the model in half at around 5mm, with the bottom part...
youmagine
Clips on the Olympus BLS-5 Battery used by the popular Pen-Cameras and covers the contacts to prevent shorts. ...It features beveled edges and corners to stop it from poking holes into your gear.
thingiverse
Dummy battery for Olympus camera BLS-5. PCB need to be developed by yourself. ...Use 10kOhm resisotr between minus and T field.
thingiverse
Remix of the BLS-5 Battery Holder of vrmmm to keep 3 batteries together Original Olympus battery fits very tight, Hahnel battery is much looser (but can be fixed by sticking some tape on the battery to make it thicker) The clips broke of on my print,...
thingiverse
Battery box for 5 BLN-1 Olympus camera batteries. original lid was a little tight ( had to pry to open) so uploaded a new lid should print more loose. batteries fit both ways so make sure curved sides are on the right side or it will be tight...
prusaprinters
The factory battery cover on my OLYMPUS BLS-50 has no clip and is easily lost.This replacement cover has a dimple finger grip which serves as a neat friction catch. The cover is lightweight, quick to print and protects exposed contacts from...