one handed ps3 controller 3d models
679997 3d models found related to one handed ps3 controller.myminifactory
This PS3 attachment is especially suited for one handed gamers, the package contains an Analog stick and L1/L2 extended triggers. They can be easily attached to any standard PS3 controller. These designs allow users who are handicapped or disabled...
grabcad
PS3 L1 and L2 extended trigger for one handed gamer
prusaprinters
See the description of the One-Handed Xbox Series attachment. This is the same device adjusted to fit the older Xbox One controllers.Two different versions are included. One for left-handed and one for right-handed gamers.Print the parts in PLA with...
prusaprinters
This One-Handed Holder will give you access to the left analog stick while only using your right hand. The base is designed to give you the freedom to place the holder on most surfaces. The Analog Stick Mod can be taken out and replaced with other...
prusaprinters
One for left-handed and one for right-handed gamers.Print the parts in PLA with regular 0.2 mm layer height settings. All parts can be printed without supports. (the A button has a built in support that you must snap off when assembling).<br>Print...
prusaprinters
The extensions for the triggers go on the arm of the central part and they are held togheter by a small printable screw.I made two versions of the mod, one for people that need the addon to play only with the right hand and the other for people that...
thingiverse
This is a joycon grip for use with one-handed with a lock so they can slide in easily. ... The rails for the joycon was edited by "Single hand Joy-Con adapter (Left) by Vexelius" with a different angle and now with a lock The grip bracket was edited by...
grabcad
4 symbols, strong as anything else in the world. ...Each one with his color, pure and pragmatic since ages
thingiverse
game clip PS3 and HTC one M7 Instructions 0.2 mm layer , black PLA
thingiverse
pwsmithy's mount had a weak section in the part that attached to the controller. I have reinforced this section and split the print into two files. ...Note: I'd recommend printing the smaller part on it's side to strengthen it, not as it is pictured in...
thingiverse
https://www.xbox.com/en-US/xbox-one/accessories/controllers/xbox-black-wireless-controller A commercial one-handed controller can be found here https://www.evilcontrollers.com/x1-unlimited-add-ons-master-mod-custom-controller To print, the minimum...
cults3d
... ... This little gadget allows you to drive one-handed, meaning you can keep your other hand free for doing something else (using a camera etc). ... Simply pushes over the foam on your DX3 steering wheel, can be set to your desired comfort position.
thingiverse
Based on PS3 Controller Under Desk / Table Hook by charlesjcarr, this hook allows keep the ps3 control under the shelf without connecting the USB cable to stay safe
thingiverse
I needed a holder for the PS3 controllers I bought for the grandkids. I wanted something light and small. Decided to design one. ...This prints best on its side with supports and raft.
thingiverse
This mount attaches to a PS3 controller and can hold the Oneplus One android phone.
thingiverse
created a wallmount for a PS3 Controller that easily snap in and fitting tight. i mounted it on a board. Btw: print it with the wallside laying on the heatbed to get a better strength at mount. PS: if you´re donwloaded this one, please leave a...
thingiverse
A simple Rack for your PS3 Controller with two holes for 4mm Countersunk Screws add 1-3 % in Cura for a better result
thingiverse
Stand for a PS3 controller. Printed with 1.75mm high temp ABS at 25% fill. Two base options. Original extends about 15mm beyond the edge of the controller. Narrow is about 10mm within the edge. ...I prefer the narrow.
thingiverse
A Ps3 controller holder. Don't fit as good than my Ps4 version but is ok. ...Print Settings Printer Brand: RepRap Printer: ...
thingiverse
I wanted an under the shelf PS3 controller holder, but found ShaoPellini's design had slight gaps on my PS3 controllers that left a slight wobble. The hole allows for the charging cable, and I've found if I stick the charging cable through both...
thingiverse
Easy to print holder for two PS3 controllers. Put it all together with contact glue. Notes: 1. You may need to sand a little bit to fit the holders into the base. 2. Take care to have the wide part of the base plate to the rear. 3. Note...