filament spool holder ender 3 3d models
1157713 3d models found related to filament spool holder ender 3.thingiverse
With this accessory the spool filament rotates very easily You will need two bearings with an inner diameter of 5mm and an outer diameter of 12mm. If you want the support of filament spool ( part 1 ) to be more stable add paper tape , but you don't...
thingiverse
Didn't really have a problem with the stock holder but using this one relieves the tension on the filament noticeably. Narrower than the stock holder. Will fit spools up to 80mm wide and an internal diameter of Ø45 +. See comparison photo. ...
thingiverse
The filler mount fits in the stock spool holder arm for the Ender 3 S1. It works really well for me whether for the left side or the right side . EDIT : Now 2 versions are available, the first for a reel diameter ranging from 35mm to 60mm, the...
thingiverse
The Ender 3 Pro spool shaft does not rotate so I figured it was simpler to have a non-rotating spool shaft for the Ender 3 S1 Pro. Although the part is printed with support, the only area of the part that is supported is the mounting detail. The...
thingiverse
This replaces the default spool holder tube/shaft that came with the Creality Ender 3 Pro™︎ I purchased a few months ago, specifically for use with a Hatchbox® PLA 1.75mm Filament spool.There are three parts to print; the Spool Shaft, Hex Nut and the...
thingiverse
Got tired of the filament rolls falling off the holder on my Ender 3 v2. Made this filament holder to fix that problem. Fitted two 608zz-bearings inside to make it turn really smooth. Depending on how tight you fasten the front holding...
thingiverse
just slide into old spool holder and then put smaller Dremel spool on shaft. ...use highter infill for strength.
thingiverse
I decided to replace the stock coil holder for Ender 3 with a holder with bearings, for a smoother ride. I considered many options already existing and none of them suited me. I decided to make my own, simple, with a small number of details. There...
thingiverse
I designed this spool holder to slides onto the 2020 top rail. It has holes for screws but I haven't had to use them. My printer doesn't print the threads in the thumbscrews all that well so I have been chasing the threads with a 1/4-20 tap. The...
thingiverse
Filament spool holder for 20 mm spools for Ender 3. The one I printed was a little weak so i updated the piece. ...That´s why it doesn´t look exactly the same.
thingiverse
Spool Holder for the Ender 3 (probably works with CR10 and other printers too). ...You just need an old drone motor, glue the bell into place and you got a nice spool holder with ball bearings :)
thingiverse
Filament/Spool Holder w/Ball Bearings for Ender 3/Pro. Uses stock nut & bracket. Can be tilted to adjust for changes in mounting angle. Requires 2 pcs. ...ball bearings 608Z/IBB (8x22x7mm) OBS: Tight fit - print vertically Alternativ...
prusaprinters
By using the original spool holder of the Ender 3 V2, the filament spool keeps swinging back and forth while printing. It is sometimes annoying as it makes some noise. Also, a more secure way for hanging the filament spool is needed to...
thingiverse
This filament spool holder mounts on top of the existing stock spool holder to reduce friction when dispensing. In contrast to other designs, this design builds on top of the stock spool holder instead of throwing away another perfectly fine part.
thingiverse
This is a secondary spool holder for an Ender 3 V2 printer. This replaces the nut on the spool holder that comes with the printer. Printing: I printed mine with supports on the inside just to help the ears print correctly. ... Do not change the...
thingiverse
This is a simple rotating filament holder sleeve that fits over the stock ender 3 (pro) filament holder. The setup uses one bearing at the end of the holder and two to support the sleeve at the mount. The sleeve has flanged ends to stop the filament...
cults3d
I really loved this project created by Pitoo67 and originally from in_the_garage so i decided to create a LIGHTER (print in much less time and use much less filament ) but still 100% working filament spool adding ONE thing it can NOW be placed on top...
thingiverse
I really loved this project created by Pitoo67 and originally from in_the_garage so i decided to create a LIGHTER (print in much less time and use much less filament ) but still 100% working filament spool adding ONE thing it can NOW be placed on top...
thingiverse
Spool filament support assembly is made out of few parts for easy printing. You need to print (1) base plate, (2) base supports and (4) brackets. ... Additional parts: - (4) bearings:...
thingiverse
drukować na pionowo jak to możliwe print vertically as possible
thingiverse
A remix of: https://www.thingiverse.com/thing:5725013 Took the original file and cut of the holder part, and just kept the attachment for the default arm that is included when you buy the Ender 3 S1 or S1 Pro. No clue if this spool arm is included in...
thingiverse
Base Unit 1- 608zz bearing (Fidget Spinner or Skate Board Bearings, standard size) 1- M5 screw about 22mm 1- M5 T nut (for mounting bearing in base) 4- M4 nuts about 20mm (for mounting base on 2020 extrusion) 4- M4 T nuts (for mounting base on 2020...
thingiverse
i ordered few of REAL brand of filament but it has cartoon spool with big diameter hole and was not so smooth movements on original ender 3 holder also i uploaded 3ds file to edit it. when i printed it, i had to very little grind of original ender...
thingiverse
It fit with oryginal spool holder Ender 3 pro Use PETG material if you use heated chamber. ... Infil 100% Minimum 3 wall line count Use Brim Bed temp: 65*C Fan speed: 10% For Nozzle 0.4mm: Nozzle temp: 230*C Layer height 0.3mm Line width 0.5mm Speed...
thingiverse
So basically here's another Spool Holder for your printer, however, the big difference with others, is that this one is designed specially to fit on the Creality Ender 3 filament/spool arm that the printer comes with. All you need to do is print the...
thingiverse
Made to eliminate a potential y axis lean of increased length ender extender z extrusions caused by the standard unbalanced spool holder. ... Print how its shown in bed photo with leaf spring pointing up, use 20% tree supports and 1x-1.1x layer height...
thingiverse
Hi, its a new spool holder with 4 berrings to Ender 3 / Pro. ... Can use 2x filament spools 0.5 kg or 1 kg
thingiverse
This version with 2cm diameter, compatible with Ender 3 original connector.
thingiverse
Filament spool holder for the Creality Ender 3. 2 hours and 15 mins of printing time with 0.2 layer height. ... Print with supports and use the black handled flathead screwdriver to remove the support from the holes after printing.