open stl file solidworks 3d models

Feel free to rescale as needed.Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1 -...

After the device turns off, wait for 30+ minutes before entering the room, then open all windows and change the air in the room during 30-60 minutes (this time may be reduced in case of strong wind). If you don’t have a timer to turn the device off...

You could make do with 0.15mm or 0.2mm for most parts, though you'd lose some detail on some of the more intricate pieces.Special consideration should be taken for these parts:Both horns need supportsMask piece 1 needs supports and may need to be...

It's indicated by a blue light, and can be ended sooner, by an additional press on the button.Range is chosen by moving the foot pedal back and forward, over the desired range.After the range is set, it is saved to EEPROM (so it's not power...

Greetings to all   Edit 21/02/2021I added a new axis in version 3.2 (I will also put the stl bundle of all the joint in version 3.2) compatible with versions 3.0 and 3.1 (in this case the shells are just the same) which optimizes the distance...

The STL filenames have the inner diameter in mm in the filename. In case you need even more different sizes, please install OpenSCAD on your own computer and follow these instructions to customize your ring.Using the ringsSo measure two fingers...

The STL filenames have both the style (normal/thin/wide) and the inner diameter in mm in the filename.In case you need even more different sizes, please install OpenSCAD on your own computer and follow these instructions to customize your...

The STL filenames have the inner diameter in mm in the filename. In case you need even more different sizes, please install OpenSCAD on your own computer and follow these instructions to customize your ring.If you could take a picture of an...

The STL filenames have the inner diameter in mm in the filename. For conversion of ring sizes, please use the “Ring size conversion table” at the end of this instructions page.<br><br>In case you need even more different sizes, please install <a...

The STL filenames have the inner diameter in mm in the filename.&nbsp;In case you need even more different sizes, please install OpenSCAD on your own computer and follow these instructions to customize your ring.Using the ringsSo measure the diameter...

Greetings to all Edit 21/02/2021 I added a new axis in version 3.2 (I will also put the stl bundle of all the joint in version 3.2) compatible with versions 3.0 and 3.1 (in this case the shells are just the same) which optimizes the distance between...

If you're still having issues then I would recommend returning to IdeaMaker, because G-code editing may be too advanced.10/31/2022 - I guess I should have mentioned, that with the recent INI file I uploaded, a lot of the code in the original details...

(REMEMBER THEY ARE NOT THREADED).The other pieces fits quite well and i updated some FIXED files with tollerances and better made design.Thanks to a comment's tip, I'll update the sensor hub base with a modular fit for different type of temp...

Lastly, I've included a .3mf file for use with PrusaSlicer 2.2.0 (or presumably later) so that you can slice your customized version yourself and not have to spend several prints to get the right settings.After over 3 years of continuous...

In that regard I have also included the full STEP file, so that anyone can modify the design as they wish to fulfil their own needs or make further improvements.* **EDIT: To make the control PCB more accessible, I've uploaded the gerber files and...

I also use a metal file to make a flat spot where the tip of the set screw touche the shaft.&nbsp;The four(4) screw clearence hole in the hub also need to be drill and tap to M5 tread.Then, fix the hub to the shaft. &nbsp;Fix the big gear to the hub....

I call it The Cerberus DISCLAIMER: By downloading these files, you agree that I shall not be liable for any damage, injury or harm resulting directly or indirectly from the use of these files or instructions. Always be safe and aware when operating...

I call it The Cerberus DISCLAIMER: By downloading these files, you agree that I shall not be liable for any damage, injury or harm resulting directly or indirectly from the use of these files or instructions. Always be safe and aware when operating...

All parts were printed from black PETG Prusament. Infil: grid, minimum 25%. The name of the file contains the number of parts needed.The file name is in the format: XX_YY_ZZx_WwwwwXX = Location in the assemblyYY = Serial numberZZ or Z = Number of...

One is marked Trigorilla the other is marked Trigorilla 1.1 . 7/11/19 Ok I have now added on to here the Hex file to clear the EEPROM as many of you have been asking for it. It is a use at your own risk file. But I have found this sorts out a number...

Remix pro 7" touch panel / Remix for 7" touchscreen https://www.thingiverse.com/thing:4646683 by David Shearer 9/2020 - EN New: STP/STEP file include I'm currently working on a new model, this design has a bit of a problem. After screwing together,...

These files are intended for the most part for laser cutting. But if you are not confused by the small size, you can also print them on a 3D printer. When downloading, do not forget that you do not need to click Download All, because in this case you...

No supports, no raft and using Stock .6 Nozzle settings on Prusa Slicer. The only files you need to print is the Main body and Turntable, everything else is included for ether reference so you can design your own using these style lamps or to check...

What is happening, that I learned with the classic view and had not used it since the last time I installed Windows (much to my regret there is no version for Linux) and total that I had no way to put the .cuix of the view classic because I didn't...

You need to print: 1x top ring part 1x left ring part 1x right ring part 1x stand/base 1x cap 3x diffuser The 3MF files was created in Prusa Slicer. I added different options. I recommend doing it with the included supports. With that, you have a...

Tolerences of the locking mechanism might be tighter depending on printing speed and quality of the filament if printed with a 0.6mm nozzle. Multiple Extruder Printers: For printers with the ability to print multiple materials at the same time you...

These files are intended for the most part for laser cutting. But if you are not confused by the small size, you can also print them on a 3D printer. When downloading, do not forget that you do not need to click Download All, because in this case you...

It contains all of the files, documentation, and images.General notesWhen it comes to donor devices, the size of PIR sensor is the main concern; the one from the aforementioned donor device has a body (not lens) diameter of 10.35 mm (the lens is...

You need to print: 1x top ring part 1x left ring part 1x right ring part 1x stand/base 1x cap 3x diffuser The 3MF files was created in Prusa Slicer. I added different options. I recommend doing it with the included supports. With that, you have a...

No flow settings for the individual bits need to be made.Print settings:5 top and bottom layers5 walls + alternative wall with infill25% gyroid infillline width 0.45 mm (outer line can be 0.4 for print quality)no support neededThe size numbers in the...