openSCAD Parametric Filament Spool Adapter 3d models

Modular Wahoo Board Shortcut v2 - This is the middle shortcut piece that I put a hole in to allow for a different colored filament to make up the center. It is recommended to use either a Modular Wahoo Board Shortcut Star Insert v2 or Modular Wahoo...

Thanks to our community user @Minoas for reporting a small problem on the Extuder+ V3 cover, we have made some adjustments so that the plastic gear moves freely.Inspired by the old Bondtech extruder for PRUSA MINI, in VERTEX, we saw the problem of...

They may work on filament printers, but we do not support that printing method as standard. STLs are provided in both pre-supported and unsupported forms. We suggest you download the free sampler pack to familiarize yourself with our formats and...

You will need black, silver, blue and red filament.There are Slide and Push versions of the Upper Handle, Lower Emitter and Switch. Internal is only used for Push. (With Push it is printed at a different orientation to reduce friction. With Slide,...

The side thickness also defines the thickness of the ribs, at the bottom of the saucer.S17 (1.68mm): The thinnest variant is best suited for rigid filament. It is ok for smaller saucers, but definitely too weak for saucers matching pots equal or...

If you use the same stuff, don't allow your gaskets to touch or they will amalgamate and prevent you removing your clamp! I printed the clamp bolt/screw in Sunlu PLA+ because the threads are better defined than with PETG, and the screw doesn't touch...

If you have the proper filament colors, no painting is needed. The assembled model is 105mm tall and is in proportion to my Sylvester model. Enjoy! **Print Instructions:**Supports: NoResolution: .2mmInfill: 10% Notes:** Refer to the notes below...

...Not suitable for filament printing. The presupported versions include "bumpers" - a small extra edge which is meant to be sanded off in finishing. These bumpers help with dimensional stability, and also prevent chipping when you remove the supports.

I've had this installed on my doors for a couple weeks now and they have been working perfectly. Upgrade plans: Move the distance sensor to the bottom and use it instead for detecting if a car is in the bay. Change the door opening detection to a top...

If you have the proper filament colors, no painting is needed. The assembled model is 235mm tall and is mostly in proportion to my previously released Looney Tunes models. Enjoy! Special shoutout to maker Benoît Lussier for providing QA printing...

The total print time of what is pictured is around 56hours and our model uses 11 different colors of filament. With that said, the Overlords were kind enough to provide us with a few different versions of the print! First and foremost, the coins come...

Make what you want. Husky Parts Organizer https://www.homedepot.com/p/Husky-10-Compartment-Interlocking-Small-Parts-Organizer-in-Black-235587/302939645 OnShape Models...

If you have the proper filament colors, no painting is needed. The assembled model is 115mm tall and is in proportion to my Winnie the Pooh model. Enjoy! ...

Other screw sizes: - e3d_clamps to main - four M3x12mm screws - top and duct to main - four M3x12mm screws - filament fan to duct - four M3x16mm screws - cable_clamp to top - two M3x16mm screws Y-stop sensor visor is published here. X rods: D=8mm...

Then add pieces of PLA filament to help you center the counterweights on the dish and glue all this in place. The two hall sensor and magnets must be put placed in way that the hall switch acts (closes) when the magnet is close to the sensor. If...

The complicated support stand is an absolute must to get a decent print for a filament printer. After all the work, I was happy to get it working and am going to leave it as is.</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p>...

I put three in, but I only use the front one because that is all that is needed to hold it closed. Print Settings Printer Brand: Prusa Printer: i3 MK3 MMU 2&lt;/div&gt;Rafts: No Supports: No&lt;/div&gt;Resolution: .15 mm Infill: 20%&lt;/div&gt;...

make sure your bridging is working good. in the main parts are 2mm holes for fitting and glueing. The grips are seperated for fuzzy printing. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: 0.2...

There are 1.75mm holes in the nubs and the top of the hand piece, so you can use a bit of filament to register them when gluing them in place. The snaps that hold the original gloves closed are separate pieces that should pressure fit into holes for...

... enclose the magnet in the print. Print Settings Rafts: No Supports: YesResolution: 0.1 mm Infill: 20% Filament: 3D Solutech PLA See Through AquaBlue Notes: See notes on the thing this was remixed form on how to print it. ... Category: Electronics

If you have the proper filament colors, no painting is needed. The assembled model is 198mm tall.. Enjoy! ........................................................................................................... Special shoutout to maker Benoît...

...And the filament also costs a few cents. So lets say 20$ in total. Important information: Length of the carbon tubes, please see the attached drawing. Cutting them roughly is good enough, a milimeter more or less is not too much of a problem.

Choose a strong filament that will be futureproof. If you plan on printing in an enclosure, I wouldn't recommend PLA due to the fact these mounts will be carrying the weight of the bed and frame and the heat could cause them to warp/sag. You will...

If you have the proper filament colors, no painting is needed. The assembled model is 175mm tall when sitting flat and approx. 240mm tall when the legs are bent. Enjoy! Special shoutout to maker Benoît Lussier for providing QA printing and quality...

In case you need advice where to get your filaments from, check our partner's website. Speed setups: Infill speed: 30mm/s Outer shell speed : 30mm/s Inner shell speed: 20mm/s Top/bottom speed: 20mm/s Support speed: 50mm/s Travel speed: 150mm/s Skirt...

3D Print Settings: * Printer used for prototyping: Prusa Mk3 * Rafts: No * Supports: None * Resolution: 0.2 mm * Infill: 20% * Filament - Hatchbox PLA, WhitePTEG or PLA are suitable. In absence of these, other materials should be acceptable as well....

The total cost for 2 lamps is approximately €50 (€20 5meters led strips + €20 2xled strip mounting profiles + €10-12 impressions) Approximate price depends on the leds and filament chosen It consists of 2 parts: - Main base: Here the led strip...

Optimized for printing, the cab and bed comes in a variety of included options.    Cab: Cab cut version (Roof is separated from cab for less supports while printing, saves more time and filament) Cab full version (roof and cab are 1 piece, looks...

If you have the proper filament colors, no painting is needed. The assembled model is 270mm tall and is mostly in proportion to my previously released Looney Tunes models. Enjoy! Special shoutout to maker Benoît Lussier (Printables id: Benoît...

They may work on filament printers, but we do not support that printing method as standard. STLs are provided in both pre-supported and unsupported forms. We suggest you download the free sampler pack to familiarize yourself with our formats and...