ostc dive computer 3d models

Heinrichs Weikamp OSTC+ coverPrint in TPU

This is a small piece that holds an **OSTC Plus** dive computer together with the wireless charger. This is especially useful if you charge your computer in your car, when driving to the diving site, as it will ensure that everything stays in place...

This is a small piece that holds an OSTC Plus dive computer together with the wireless charger.This is especially useful if you charge your computer in your car, when driving to the diving site, as it will ensure that everything stays in place and...

While diving I nearly lost my Galileo Sol computer when the wrist band suddenly broke.It was a few years old, and for a computer so pricey it definitely should not break so young.They will soon stop making them so they will be hard to replace.Here is...

This is an upgrade, or modification, for a Suunto Eon Steel dive computer allowing it to sit comfortably on the side of the hand rather than the back. This makes it easier to view the computer underwater - especially with a bulky dry suit. The STL...

This creation is designed for the VR3 dive computer and you can use it as a bangee holder.

As an underwater photographer, I hold my camera and need to simultaneously see my dive computer. The computer naturally sits on the top or bottom side of my wrist. However the edge of my wrist is facing up when I am holding the camera. I needed a way...

Printer Settings: Printer Brand: RepRap Printer Model: Velleman K8200 Rafts Required: No Supports Needed: No Resolution Setting: 0.5 mm Infill Pattern: Solid Post-Printing Instructions: Remove the original bracelet from the Aladin dive computer and...

I designed this simple stand for my Mares Matrix wrist dive computer that makes charging and syncing easy while keeping access to its buttons open. The charger base stays securely in place, allowing me to simply lift the watch out of it and slide it...

Replacement for the bracelet. Print instructionsCategory: Sport &amp; Outdoors Summary Bungee links for the Aladin dive computer. Replacement for the bracelet.</p> <h3> Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>RepRap</p> <p...

Used to protect a D9 computer when transported Print Settings Printer: Original Prusa i3 Rafts: No Supports: No Resolution: .2 PLA or .2 PET Infill: 20% honeycomb in translucent PLA looks interesting, but otherwise up to you Notes: Prints just...

Suex DPV dive computer t-fix mount

The user interface of Suunto Zoop connects directly to your PC via a convenient dive computer cable plug-in.

Adapter that allows you to mount the Garmin Descent MK1 diving computer using bungee cords. A perfect solution if you want to use a computer, e.g. with a dry suit. Print with pet-g. ...I recommend the filling 100%

This protective case is specifically designed for the Suunto D4 dive computer, allowing you to transport it in your bag alongside other dive equipment without worrying about damage. ...You may also want to apply a small amount of silicone grease to the...

This is the upgraded version of the Scubapro Sport, Aladin or compatible dive computer.\r\nTo create your custom strap, you can combine two pre-assembled components: a 30mm piece and a 36mm piece where you can attach the final closure...

This is an updated version of my previous dive computer case for Suunto D4(i), inspired by the waterproof match case design. I've added a profile to improve grip when opening and closing, a seal printed from flexible material, and the Suunto logo on...

Depending on the thickness of the acrylic you choose to use, you might need to remove the metal front off the dive computer if it can't be bent. I used 2mm thickness and believe it's an improvement over the original protector. I've included the...

To tighten once on your arm, the section going across the back of the computer can be pulled over the top and held in place by the lip on the front. ...Change how far down the cord the final knot is tied depending on how thick of a wetsuit you are...

The mount for the wireless charger is slightly off center to have the charger position aligned with the position of the charging coil inside the dive computer. ...The longer of the vertical arms is meant to go towards the rounded edge with the 'OSTC'...

The longer of the vertical arms is meant to go towards the rounded edge with the 'OSTC' label on it.Update (23 Oct 2022): I've updated the design with less room for the dive computer to move around, in order to keep it in the right spot for the...

A guard Ring for Suunto Vyper Novo 2023, with click system and 4 buttons with fingergrid. ... There is no signature on this model. It also fits on Zoop Novo, Vyper Air, i think. Scuba Diving Computer Diving Computer

This is a reconstruction reengineering of a boot for a Oceanic dive computer type VTpro. It might fit to other VT models. Mine was brittle and fell apart after my last dive. Please make sure your computer is in proper condition. Have an inspection...

heinrichs weikamp OSTC 2 ( > v2017) protection coverOne version is to print with hard plastic :PLA or PETGThe other is for TPU

Bonjour à tous, Voici un support pour le chargeur par induction d'un OSTC Plus, conçu selon une idée originale de "Claude" : https://forum.heinrichsweikamp.com/read.php?7,17119. Le dessin a été entièrement remodelé avec FreeCad et adapté aux...

Protective housing for Ratio iX3M

Here is a small tool to easily remove the battery cover of the OSTC 2C. ... This project was inspired by two designs found on Thingiverse, specifically: * https://www.thingiverse.com/thing:2794544 * https://www.thingiverse.com/thing:2263494

This is an updated version of my [OSTC 2C Battery Cover Remover](https://www.thingiverse.com/thing:3475033). Multiple T-pieces can be printed and replace an old broken one. Can someone make a metal version or a more sturdy version of the...

Protection Cover For Dive Computer - Suunto ZOOP Settings 3D printing: Top Solid Layers - Six Bottom Solid Layers - Six Outline/Shells Perimeter - Three Thin Infill Density - Twenty-Five Percent Support Structures Required - Yes, Limited to Build...

... B.U.D BackUp Device having given up the ghost several years ago, and following the acquisition of a 3D printer, I started to build this bracket for Puck. The only thing left of my B.U.D is the carabiner! Good day and good diving to all, Benj