phone holder for toyota 4runner 3d models
2438460 3d models found related to phone holder for toyota 4runner.thingiverse
It is a friction fit for both the USB cable (into this holder) and the holder (into the blank slot on the 4runner). ...Friction fit was used to facilitate removal (use a small bit of E6000 glue on the back of the largest lip if you need a more secure...
thingiverse
This is to hold the USB cable end for the Cartrimhome T10 head unit for Toyota 4runner. It fits into any blank slot in a 5th generation 4runner. It is a friction fit only (both for the USB cable and the fit into the blank slot), so you may have some...
thingiverse
The rear cup holder in our 2000 3rd gen Toyota 4Runner had seen better days. The left arm had snapped off and was lost forever. This isn't an exact copy of the original, but it's close enough that it works in all the ways that matter. ...To make sure I...
thingiverse
I was looking for cellphone holder for my 4Runner, I was already using one of those magnets that stick to the air vents. The problem was that I could not redirect the vent and also the iPhone would be facing away from my face thus I was not able to...
thingiverse
It is partially recessed in the pocket (for extra stability) and uses the 2 factory screws for attachment. It also has pockets in the back for (4) 1/4 28 nuts. (2) Mount plate: This plate mounts to the adapter plate. It is set up for 1/4 28 x 1"...
thingiverse
Working on designing a phone holder for random compartments on a 2020 4runner. ...This design is for a wireless charging puck.
thingiverse
Switch holder for 90-95 4runner and pickup
thingiverse
I lost the cupholder insert for my 2005 Toyota 4Runner, so I designed one that fits perfectly in the console. ...I added 2 holes for pens or straws and a credit card/loyalty card slot.
thingiverse
Cup holder fits inside the rubber cup holder insert for the 4Runner. Best fit for the cup holder near the front. You must have the rubber OEM cup holder insert for this to fit properly. Super Glue the base to the top, off set from the center,...
thingiverse
I made a simple hanger for a Rexing Dashcam rear camera to hang from the ceiling liner near the weather stripping and roof come together.
thingiverse
UPDATE 2: Added two more top mounts for a captive 10mm or 8 mm nut or bolt for other mounting options 3rd Gen 4Runner clock insert phone mount. 3 piece robust design with very little support needed when printing, you'll need 8 dollars in additional...
thingiverse
Smartphone holder for TOYOTA new SIENTA We designed it so that the in-vehicle monitor and smartphone can be used at the same line of sight. ... This is trial model by PLA, and I will print by PETG.
cgtrader
Wheel For Toyota 4Runner Trail Original 3D Model
cgtrader
''Proline 4x4 Equipment'' for ''Toyota 4Runner sr5/TRDpro'' 3D model
thingiverse
Made to hold a phone in a 2018 rav4. ...Prints in 4 parts, no supports needed. With a hole at the bottom for charger to be able to go through. ...Glue bottom shaft to base plate and top part swivels without hitting the shifter or blocking cupholders.
cgtrader
Bumper Front ARB For Toyota 4Runner 1999-2002-3D Model Modeling in Autodesk 3Ds Max 2010 Screenshot in Zmodeler 2.2.4
grabcad
Toyota 4runner front bumper, only renders.For more information about the DIY plans kits consult via instagram
thingiverse
This part is used to mount an Anytone AT-5888UV radio in the center console storage of a 4th generation Toyota 4Runner You can see the mount for the body here:http://www.thingiverse.com/thing:2155881
thingiverse
5th Gen 4runner cup holder reducer insert to replace the stock one that gets stuck on the bottom of mugs then lost forever. Made from scratch in freecad. The small without handle is perfect for contigo mugs. The large without handle is perfect...
thingiverse
Remixed Toyota 4runner keychain, modified to be slightly thicker and wider with toyota wording across the top.
thingiverse
This part is used to mount the body of an Anytone AT-5888UV radio behind the rear right-hand cargo compartment of a 4th generation Toyota 4Runner. ...You can see the mount for the head unit here:http://www.thingiverse.com/thing:2155879
thingiverse
For my 1st generation (1987 )Toyota 4Runner, this clip holds the grill to the truck body. These grill clips are very similar to the stock clips. ... Instructions Solidworks and calipers.
thingiverse
... back. The hole is oversized so there is an adapter ring...and a plug of you wanted to use it for smart phone storage or the like. ... Also included in the design are square holes in front for adding optional accessories like a smartphone mount...
thingiverse
Designed a dashcam mount for the Viofo A129 Pro Duo rear camera, to be screwed into the center upholstery pin of a Toyota 4Runner with an M6x20 Bolt. Curves to the roof to keep it straight, almost no movement whatsoever of the camera. Camera fits...
cults3d
3 inch cup holder with room for a phone and 2 pen holders. attached with double sided tape and 3 sheet metal screws from the back side. a little wobbly but works ok. ...could use a support arm but I didn't feel like getting too crazy with the design.