pilot g2 mod 3d models

I decided to do not mod it, but rebuild it fully. Only frame PSU, MOSFET and motors I used to this new project.<br/> Project goals:<br/> adopted from prusa:<br/> original mk3s rambo board with excellent prusa firmware and tmc 2130 silent drivers...

I found this super mod but it doesn't work with hinged lid.https://www.printables.com/cs/model/276123-prusa-enclosure-ptfe-tube-guide/commentsThat's why I tried my own attempt to guide the filament the old way. Unit for guiding the filament is...

Be aware that different manufacturers of LED-strips use different sizes of LEDs and width of strips, you might need to modify the profile of the ring to match yours!This version takes it’s power directly from the USB-cable of the Nano with no extra...

This thing is a modular desk extension for keeping books, stationery and private things at its place and away from the desk working area. Print Settings Rafts: Doesn't Matter Supports: Yes **Notes:** I had to invest some time modding and...

Send me a DM for the link or any requests for mods/changes/versions.Post your make!Please post 'em! Really! Take a quick cameraphone photo of your print in all its glory and show it off! Plus it really helps get this design out there to the...

One can usually install this without re-plugging things on their toolhead… Including the CAN Bus cable if relevant, as the cutout in the PG07 mount allows getting this around the cable from the side.Works well with 3010 fan modded cable door:...

Send me a DM for the link or any requests for mods/changes/versions. Post your make! Please post 'em! Really! Take a quick cameraphone photo of your print in all its glory and show it off! Plus it really helps get this design out there to the...

Let me start to thank user 0110-M-P from Thingiverse for sharing his work in Thingiverse: https://www.thingiverse.com/thing:922740 I remixed his great job to obtain following results: active cooling with Noctua 40x10 5V fan less possible hardware...

This is a remix from a good fitting design a friend shared with me, which can be found on Thingiverse here: (Note, I would have marked this as a “remix” the PrusaPrinters way, but it wasn't working correctly, so this is my workaround)Graflex 4x5 Lens...

I've used reference images and materials to gather the measurements for this mod. If you print one, let me know how it fits and if there are any suggestions.</p> <p>I've currently made no special allowance for how a 6pin DIN connector will fit. So,...

Looks like they are MOD 1 gears. The Autodesk disclaimer on the correctness and suitablility was found in the C++ code. /************************************************************************************** Author-Brian Ekins Description-Creates a...

The adapter may have a little play; this is OK and does not affect the strength or functionality of the adapter. If you don't like the design or fitting, I've also gone ahead and included the STEP file for you modding pleasure. ...Let me know what you...

Out of respect for the author, I am not providing the complete set of files here (despite the model being distributed on DC without a license), only the ones that I have modified for this purpose. This mod allows you to print everything FLAT. ...This...

This is a remix from https://www.thingiverse.com/thing:398515This remix adds some custom parts and replacements for some of the aluminum parts2 sets of nameplates (side plates):Hex - hex all the thingsTF - just the initials of the...

This is a mod for https://www.thingiverse.com/thing:104028/remixes I gave away my Apple Time Capsule only two nights ago, and had no use for its home of five years. So I gussied it up, covered the windows with white paper, stuck a LIFX inside, and...

Here is a cooling duct I designed as I couldn't find anything to suit my needs.My requirements were:Use 2 4020 or 4010 fansDirect drive with BMGStock hotendNo loss in build heightGreat access to heater blockVoron inspired ish :)BLtouch mountCable...

Welcome to check out my youtube channel: I made 3d printer reviews videos, tutorial, mod, and more.                      https://www.youtube.com/channel/UCBjyI1E1HROh1BAYgeRZy7g           Support my work: (click on image)                             ...

Melt, tape or glue the parts together. "pcb" is for pcb mounting, it will slip over the top of termimals soldered to a board, the centre terminal spacing to the middle of the metal on the pcb is 68.54mm according to the design. Not tried printing the...

so be warned if you want to resolder these. Leds as photographed are at around 10% brightness as I am only using a 600mA 5V supply and the matrix full power is 3.5A. Added the arduion sketch too, its messy as it was a quick hack though others may...

... nearly as strong). Loctite makes a similar plastic epoxy. You may wish to place a small bit of foil in the valley below the glue joint to catch glue that drips. F360 archive provided if you wish to remix or mod. Category: 3D Printer Accessories

This is a mod for the new creality CR-6 SE/Max to replace the stock (noisy!) 40 mm part cooling fan with a larger (and quieter) 40x10 mm fan. ...The supply is 24V.</p> <p>The metal protection will have to be removed to use this.<br/> Use this together...

Instructions WARNING: This mod could potentially void your warranty. Use at your own risk! Print 2 idler pulleys using standard or high settings. Allow Mini's extruder to cool, then turn off and unplug the power cord. The idler pulleys are located...

It is used to support both the x and y axis cable-chains. Everything is mounted with M3 screws similar to those needed for the build. Watch along on YouTube while I put together a MultibotCNCv2 of my own. printing ep1 ep2 ep3 ep4 ep5 ep6 ep7 ep8 ep9...

I don't know if I'm allowed to post a patreon link, so I'll wait on posting it (mods, please PM me). Total spent on single 5i5 10Gbe setup (including the Mellanox card): $43.68. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No...

I used an SMD LED on a pin header but a standard white 3mm one would work too and is probably easier to aim where you want it.&nbsp;Make sure your LED doesn't extend below the nozzle - you don't want it to catch on your print!To avoid scratching your...

1 system per mod. If this is your first night at Plumbing Club, you've got to plumb. This is intended for low pressure return pipes for grey water at approximately room temperature. Do not use on Gas (Propane, LPG, Butane, Domestic Gas supplies, or...

One system at a time per mod is necessary for any kind of modification. If you're new to Plumbing Club, first get the pipes flowing properly before attempting any modifications. This Ø22mm Straight Coupling is designed specifically for low...

So, the other day i dropped my bottomfed Mod and it perfectly landed heads first on the ground. Intrestingly the drip tip scattered into a douzen pieces.</p> <p>Well since we're here, lets design a custom one.</p> <p>You can either print it as is,...

NERF Super Soaker scatter blaster Mod Add an extra water tank to your NERF Super Soaker perfect for the Sommer. The Tank uses the existing Cab and is easy to Install and removable....

UPDATE : Corrected Belt dimensions in the BOM Here is my Dual Leadscrew Z-axis Mod for the K8200 (3drag). It makes the z-arm much more sturdy and results in a lot smoother prints. It is based on my hanging z axis mount...