pine tree 3d model

They also cut along main aspects of the model that would result in much needed cleanup on reassembly. The original was also designed more as a prop than a mask to wear. Since it had no breathing holes, I added some that were in the spirit of the...

Credits for the original model goes to "Babyjail" https://www.thingiverse.com/babyjail/designs be aware ORIGINAL DESIGN DOES NOT FIT BMG CLONE EXTRUDER, if you don't like BLTouch, don't have it or whatever, it will work without it too PLEASE READ...

If you want to use a Raspberry Pi camera, print out the picasetop_V3_picameraslit.stl for the camera ribbon slit and a pi case like this that accepts a screw: https://www.thingiverse.com/thing:299529 Can the camera position be adjusted for different...

Presupported files are included for each model in both STL format and LYS (Lychee Slicer) format so you can rescale them if required.  Presupports have been created and tested by Ty Mansifled, at The Tabletop Engineers. more minis are released each...

You may write me if you want to get additional support or want to get source models. Post-Printing Assembly Manual To make a full cube, first print six sides and six sets of pins. You can print fewer pin sets, but make sure you'll have enough to...

Each model is approximately 65 mm in its largest dimension. I haven't had a chance to check tolerances, so I would recommend checking the GCode before printing and making sure your printer can handle small parts. As I print them, I will try updating...

This isn't exactly a remix - I used their ideas as inspiration, but completely modeled from scratch. Credit where credit is due for the idea.\r\n\r\nI like playing Elite Dangerous on the couch in VR with HOTAS, but it's either unstable when separated...

This model employs three 400-watt power supplies: two for the heatbed connected to the Ramps 1.4 board with 12-volt automotive relays rated at 60 amps each at 14.4 VDC; and a third supply powers the extruder, motors, and L.E.D. LEDs. Heating the...

 All parts are fairly straightforward if you go to slice them on your own and I have called out orientation and quantities in the individual model files.  The Cup is a 2-piece, friction-fit assembly, but you can use just the Liner or just...

This also means that if you wanted to try to build a GoN NERD/NERD TKL, H87a, or the Kprepublic XD87 should all be able to fit - possibly with some small custimization to the model. More to come as I sort this out, but the files themselves are ready...

I modeled in additional material to make it easier to get the card into the proper spot. 8 Recess in base to allow for a low profile heat sink set. (I like these: http://amzn.to/2FYbaz6) Version 1: Some of the features I included are: Slots above...

 This design is really more of a remix of fasteddy's model, and I designed this mount heavily borrowing some of the design ideas/elements from the original.The updated support arms are based on the R3 version of the xLCD cover from MK4/MK3.9...

Huge respect to Alexey Pavlenko for the idea of adapting the popular knife from Giacomini for printing ===================================== PS 21.03.05 I updated the files of this model. If you downloaded the files earlier than this date, my...

These design criteria, along with my limited fusion360 skills, has led to the final model posted. BILL OF MATERIALS 4 x Screws & Anchors (M4) https://www.amazon.ca/gp/product/B07HQ4YMYY/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 2 x...

Models of blunt safety tips are included for shafts with and without inserts and can be glued in place. For 13xx pump guns, replace the front sight plug assembly with the included plug. The forearm liner is recommended:...

This add-on might fit on the other models this is based on like rmcht’s Double Gear Grinder and the Dual Drive system of claxly. There would be more overhang opposite the drive gear. I haven’t tried this unit on any of those. This is a simple...

The Pyramid Stacker is angled to match the exact dimensions of a real pyramid, making it a versatile storage solution with a unique look that's great for everything from jewelry and electronic parts to Lego and other small toys/models, tools, and...

The design that inspired me to fully recreate this model using similar concepts is: https://www.thingiverse.com/thing:2243280 ERPEL09 came up with an excellent concept, but the details just didn't work for the current machines. The main issue that I...

... into a single set rather than repeat the same figure in several sets. If I have omitted something important, message me. These models by waynemc65 are licensed under the Creative Commons - Attribution - Non-Commercial - Share Alike license.

As seen in the images, one of the screws is different, instead of those marks they have a continuous line (4 blue and one yellow), it is a previous model that I have reused, at the appropriate height I inserted a piece of filament from another color...

The thread is 5.5mm deep.) 20%+ honeycomb infill (higher density recommended for non-PC material) Generate supports only on build plate (upper supports are baked into the model already) Detect bridging perimeters on Support overhang threshold angle...

This is partially based on 05WEL's "Ozito battery to Xfinity (Aldi) battery adaptor" at https://www.printables.com/model/206655-ozito-battery-to-xfinity-aldi-battery-adaptor and partially based on AgentGene's "M18 to black & decker 18v adapter" at...

No glue was needed on the model.Ideas:Room name tag displays: Using bigger ePaper displays with this solution could become an easy naming system for rooms in an office, where you can change the names more easy without to cut out paper labels again...

But this is exactly a training model, it can be assembled from any more or less suitable components, because there is a lot of free space in the case. Assembly video - https://www.youtube.com/watch?v=ru8aeFB4xmo Plastic parts are printed with...

If yours is too tight or loose, simply scale the model to adjust the inner diameter that holds the magnet. ODIDScale...

Print settings for my models include an average layer height of 0.3mm achieved with high-quality ABS materials. ... During trials on the UpPlus2 printer, certain designs demanded orientation changes at precisely calculated angles – most notably for...

Therefore I'm able to connect the geiger counter to my Home Assistant + I added a small OLED Display, to see all data directly when standing in front of it (+ 10 coolness).After the electronics where finished, I've designed an enclosure, based on the...

Research I found two suitable models on Thingiverse which I thought could be easily enough modified: Tweezers for SMD by Ruslan_Kulibin SMD Test clamp by Tom20170 which I both printed yesterday. They are both quite nice designs, I especially like the...

The COMPLETE Goldmaw Lizards bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! These cold-blood creatures are at the top of the food chain in their jungle. Hunters and Warriors...

This is so that the bow string has less friction on the bolt guide rail.Effectively, this should reduce wear on the string as well as increase the effective force (due to reduced friction loss). Printing InstructionsMaterial: TPU - needs to be...