pipe printer 3d models
367172 3d models found related to pipe printer.thingiverse
DELTA PIPE PRINTER (DPP) Please see the DELTA PIPE PRINTER STEP 1 TOP FRAME for more references and instructions http://www.thingiverse.com/thing:1344167 They are no file to download, the configuration.scad is needed to be able to upload this step.
thingiverse
DELTA PIPE PRINTER (DPP) Please see the DELTA PIPE PRINTER STEP 1 TOP FRAME for more references and instructions http://www.thingiverse.com/thing:1344167 Custom Section INTRODUCTIONS This idler end fit directly into the pipe. The location is at 1...
prusaprinters
DELTA PIPE PRINTER (DPP) Please see the DELTA PIPE PRINTER STEP 1 TOP FRAME for more references and instructions http://www.thingiverse.com/thing:1344167 They are no file to download, the configuration.scad is needed to be able to upload this step....
thingiverse
DELTA PIPE PRINTER (DPP) Please see the DELTA PIPE PRINTER STEP 1 TOP FRAME for more references and instructions http://www.thingiverse.com/thing:1344167 They are no file to download, the configuration.scad is needed to be able to upload this step. ...
thingiverse
DELTA PIPE PRINTER (DPP) Please see the DELTA PIPE PRINTER STEP 1 TOP FRAME for more references and instructions http://www.thingiverse.com/thing:1344167 They are no file to download, the configuration.scad is needed to be able to upload this step. ...
thingiverse
DELTA PIPE PRINTER (DPP) Please see the DELTA PIPE PRINTER STEP 1 TOP FRAME for more references and instructions http://www.thingiverse.com/thing:1344167 The good thing about this design so far is the stepper motor float over the desk, better...
thingiverse
Hard to cut lines on the tour (carriage are in the pipe, 2 balls go out for the magnetic arm, need a router table to cut unless other technique is used) I will update this THING over time since my printer is a work in progress. If you try to make it...
prusaprinters
After some research it's was possible, ABS pipe have 60 degrees angle, I decided to give a try and make one. This is a work in progress, all the files will be available soon, hopefully some will help to improve some of the part if needed. This should...
thingiverse
Made for my dust collection system with 50mm push fit waste pipe. ...Designed for IDEX printers, as it has 2x parts, with the crush ring designed to be printed in TPU. ... Only uploaded in STEP to encourage more advanced users.
thingiverse
I designed this to mount my biqu bx screen to the stainless steel pipe that measured 17mm on my 3d printer enclosure https://www.amazon.com/dp/B093H1J46W. I didn't have easy access to the SD slot on the screen with the hinge mount with this I do.. ...
thingiverse
Remixed the pipe to work with my Adventurer 3 printer. ... Split the pipe in half using a tongue and groove joint so it fits on a 150mm bed.
thingiverse
Customized version of http://www.thingiverse.com/thing:731318 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=731318 Instructions Using the following options:...
thingiverse
for metal pipe 25.4 mm necessary fasteners square nut DIN 562 M4 screw DIN 912 M4x10 or set screw DIN 913 M4x8
thingiverse
With this adapter you can pull your unhealthy 3D printer fumes to outside. Another benefit, it will make the fan much more quiet. I used cheap installation tubes for wire management. Fan: 60 mm Pipe dia. (inner): 25 mm Sketchup project file...
thingiverse
Piper Infinity shares main design of the gantry parts with Piper 2 3d printer: https://www.thingiverse.com/thing:3294998 Working Piper Infinity: https://youtu.be/C2brIMrcJVI For more information and assembly instructions visit...
thingiverse
Customized version of http://www.thingiverse.com/thing:731318 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=731318 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:731318 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=731318 Instructions Using the following options:...
thingiverse
I designed this to adapt a small fan to circulate air through a coil made out of black abs pipe with an inner diameter of 33.5mm. this is for a compost heat system I am using to heat my greenhouse in the winter. the other square is a lid to secure...
thingiverse
3D Printer Extruder Motor Water Cooling - 2x5mm Silicone Pipes to 4mm Bowden PTFE Tube Clip. ... Designed for silicone pipes selling by Trianglelab with this set: Trianglelab Stepper motor water cooling upgrade kit for Nema17 motor.
thingiverse
(My previous printer Piper 1.2 is currently available in 2 designs, for US https://www.thingiverse.com/thing:2966295 and UK EMT conduits https://www.thingiverse.com/thing:2999885) Instructions for assembly of the printer and BOM are at...
thingiverse
US version of Piper 2 is at https://www.thingiverse.com/thing:3022836 (My previous printer Piper 1.2 is currently available in 2 designs, for US https://www.thingiverse.com/thing:2966295 and UK EMT conduits https://www.thingiverse.com/thing:2999885)...
thingiverse
Customized version of http://www.thingiverse.com/thing:731318 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=731318 Instructions Using the following options:...
thingiverse
These are braces originally designed for stiffening the frame of my Anet A2, but would be suitable for the Tevo Tarantula or really any time one would need to stiffen a 20mm extrusion frame cheaply. These could probably use some refinement, but...
thingiverse
Just a remix of the Square parts, to print in one piece, 24cm x 24cm Can be printed on both side, no support needed
thingiverse
Cover for DN75 Outdoor Pipe Stable Cover to seal a DN 75 Outdoor Pipe with the posibility to glue the cover on the pipe. ... Printer: Anycubic Vyper Infill: 25 % gyroid Layer Height: 0,3 mm Filament Material: PETG