pipeline drawing 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

TO DO Just the drawing for the dark red LED filter window. It's just an obround with two indents where the pins are, they are melted over to hold the filter. NOTE: this takes a while to render in OpenSCAD as $fn is set to 170, but drop it to 25 for...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

The drawings have been updated since I last machined the parts. You may need a rear (read: longer) QR skewer since the effective clamping width is going to be much longer. Dimensions in inch/mm since I was working in a machine shop with an imperial...

All of the other ports should be accessible, depending upon the size of your connectors.If you look at the photos, you will see that one of the cut-away drawings shows some mock connectors (Ethernet, keyboard receiver, and USB-C power) in purple. Be...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 34 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

Once you get it where you want it, draw a couple of lines to mark it. Remove the clamp and handle - keep the body on the bucket. Put CA glue (super glue) on the sides of the body, pull the handle apart a little (it will have some flex) and release...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

This is to allow for easy switching of 6V battery to USB power and vice versa, without any alteration on the wiring side.Caution: Make sure your LEDs polarity is correct before you solder them in place (refer to the manufacturer design drawing for...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

https://www.larsonelectronics.com/product/151096/25w-explosion-proof-white-led-indicator-light-c1d1-2-c2d1-2-aluminum-housing-9-60vdc-10-cordMade in TexasThe EXHL-TRN-LE4-WHT-1224-EYM-10C from Larson Electronics is an Explosion Proof Low Voltage...

REPORTING POINTS: Moving part not remaining horizontal in relation to the fixed part (aesthetic defect) Rounded parts on a fixed trolley CAUSES: Depending on the age of the belts, or the tension adjustment, it may happen that the mobile carriage...

(Sourced parts will be revealed in the post-printing section soon) - Updated the schematic drawings (Take these with a pinch of salt, although the measurements are accurate, I've probably included useless information. - The copper coloured things...

I took the wood panel laser cut design from: http://www.thingiverse.com/thing:34570 by Docmooney Even though Docmooney posted his DXF drawings of the wood panels with two thicknesses shown in the names, I used 12mm (1/2" nominal) baltic birch plywood...

Here are some additional notes about the project: * The clock has a power consumption of 5W and a current draw of 2A. * The clock has a size of 10 cm x 10 cm x 5 cm and weighs 1 kg. * The clock uses a stepper motor to drive the gears, which in...

The architect did not want the statue to symbolise violence and war, and decided to draw his Liberty standing still and clothed in long, flowing robes. His early models all showed a female figure in a neoclassical style, with an Ancient Roman style...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 1 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

Let me know if you have ideas for design changes and I am happy to draw alternative parts. Happy making!</strong></p><p>&nbsp;</p><p>PS: be realistic about the expectations of astronomical views, this telescope cannot compete with large telescopes -...

You can export the customized part in various formats including STL and STEP.Customize Arm StraightCustomize Arm RotatedCustomize Axis ChangerThe drawing below explains which configuration parameters affect which dimension.In Onshape, tweak the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

I have taken the basic dimensions from a 1/87 set of scale drawings published on pages 145/146 of the book ‘Die Panzerzüge des Duetschen Reiches’ (Wolfgang Sawodny, EK Verlag ISBN 3-88255-678-1). Since there were no given dimensions, and I have been...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

With that drawing as a template, we built a few prototypes of the body and legs before settling on the parts that have been uploaded. According to my son, "It's perfect, exactly what I wanted." We hope the maker community enjoys it as well. ###...

When the dot is stable and doesn't draw circles, epoxy or CA glue it into position permanently tighten the screws. It is now aligned on the axis. Use APC has a nice video using their tool https://youtu.be/qF-iK_BElBM Remove the K40 lens. Insert the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

So I have designed a unit that draws air out of the enclosure through a pair of 3M vapour filters and then exits this air to atmosphere through a Dyson v7/v8 vacuum HEPA filter. I chose 3M &amp; Dyson because in my opinion they are leaders in their...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...