playground swing 3d models

 If you also made this mistake (or if you like the look of the colour-matched annotation labels), I have uploaded those “caps” in the model file “Fix for Rotated Board.zip”Print each label with the dimensions 185mm x 12mm x 4.78mm. (You may need...

A round-pole design makes the assembly easier to handle and transport compared to square-shaped models.A horizontal T-mount platform is provided at the top of the tower for mounting customer-provided equipment. The tripod features a rotatable head...

BLTouch (v3.1) install on a Sidewinder X2There isn’t a lot of published information on whether or not this will work.  I’m accustomed to doing things both wrong and the hard way, so after the probe broke on my X2 I decided it was time to...

I should snuggly fit with this model: https://www.printables.com/model/123074-ceiling-camera-mount-2-axis.03: Added the grow lights for indoor plants, see pictures. Also added a section describing the little differences. Earth anchor is good to go...

Then slide the little clip (that's included with the Vertical Stand model) down the back of the Wall Mount (long side pointing down and farthest away from the Wall Mount) until it slides over the back side of the Vertical Stand. It's purpose is to...

Winston sculpted reproduction of Schwarzenegger's face in several poses out of silicone, clay and plaster.[41] The sequences set in 2029 and the stop-motion scenes were developed by Fantasy II, a special effects company headed by Gene Warren...

# What you'll need This will work with any CH340 USB-serial chip I think, but the model here is for the CH340N for USBC. A picture of the exact chip is given. I ordered one from AliExpress for about $3, and one from eBay for about $6 (because it was...

I used this 5/8" tall flat bellows available from McMaster Carr:https://www.mcmaster.com/1320K111/These bellows are made for this job and are resistant to oils, lubricants, and heat.The models are designed to fit an Eerie Tools SM-LTHM 7x14 lathe but...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

Scaling up the model to increase the included printing gap, will stop it fusing if this occurs.Step 5Now to starting turning the collar back and forth to try and loosen it up. The box closes by twisting the upper collar anti-clockwise (this can be...

If you want it without internal battery, I have designed this same model without the hole for the battery, remaining in measurements of 126x51x35mm, you have it here: https://www.thingiverse.com/thing:6016310 Required Components: - 1u Mini ZVS...

If you want it with an internal battery, I have designed this same model with a hole for the battery, measuring 126x85x35mm, you have it here: https://www.thingiverse.com/thing:6016217 Required Components: - 1u Mini ZVS Module 5-12v (...

A wrench is used to unscrew the end caps for re-lamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap.7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

We also offer other variations of this light if needed to fit your specific application, 120-277V AC, 12-24V DC, and 0-10V dimmable models.Our EPL-24-2L-LED-347V LED light fixture is NRTL Listed for United States and Canada approved for use in paint...

We also offer other variations of this light if needed to fit your specific application, 120-277V AC, 12-24V DC, and 0-10V dimmable models.Our EPL-24-2L-LED-480V LED light fixture is NRTL Listed for United States and Canada approved for use in paint...

Every link piece adds roughly 2,5 cm or 1 inch. Step eight:Cut Filament to 2,3 cm and attach the body strap to Piece K connector strap. Step nine:Cut again Filament to 2,3 cm and attach the N handles to M handle attachment:Congratulation, you just...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

EX6 Arcade Fight Stick What started as just doing a few tweaks to an existing model turned into a near full redesign and a (almost) fully printable arcade/fight stick case platform; the EX6. Printable on the Ender 3 or any 200x200 printer. The...

The pictures and model views all show the right hand frame. Most of the parts print without supports except for the inside half of the spool, handle post and reel frame that require “supports on build plate only”. I also use 100% infill for all...

... all STEP files are added for whoever wants to remix/adjust to there liking. Since I always tend to get frustrated by only having STL files of models that I want to improve/adjust I want to save you the pain of this and enable you to be creative :-).

I just have to choose a bulb of the wattage I want and with a high CRI to get the best image quality.Since Fresnel spotlights are a classic in the world of cinema, I based my project on a model of the Arri brand from the 1940s. Which has a spindle as...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

# Introduction This is a remix of the Ender 3 HallON v3 Installation kit to fit a Micro Swiss Direct Drive set-up (recent models with additional screw holes on the left. Because I noticed that the hold of the sensor in the adapter gets loose after...

The shoe lace is optional but it's a good way to secure the handle from unfolding when you don't use it.Print SettingsDon't rotate the models when placing them in your slicer. I have placed the parts in the best orientation possible with surface...

The tubes used for processing in the Whirlwind would end up leading Ken Olson to transistors, which led to the transistorized TX-O (the love of many a tech model railroad clubber) and later to Olson founding DEC. Suddenly, the Whirlwind was the...

AnyCubic Photon Heater with Optional Light Models for for the Left or Right panel For the fan I turned it around after I found it not blowing outward. Double Check You use the right top and back that go together. Don't do Like I did in the...

I added a switch at the bottom of the right arm (super easy access).Please note, this system is designed to be mounted on an aluminum profile with a total width of 300mmPrints without support!Here you will find the links to the creations that have...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 347-480V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture. .Wiring: These LED light fixtures...

The automatic transmission in some models has a tendency to fail prematurely. This usually happens around an average mileage of 108,000. **1.1 Identifying Transmission Issues** Transmission failure can be determined through comprehensive...

They should easily fit even on small printers; if you can print Hadley, you can print this mount.The mount uses a vinyl disk that sits on top of teflon pads, for very smooth motion.It is very lightweight, and can easily disassembled for compact...