thingiverse
This piece is an adapter for a skate truck, in this case, this adapter is designed for a normal Venture truck, is placed under the pedals and is ready for an evolution cockpit playseat. Any skate truck should be valid, but the wheels may be slightly...
thingiverse
This is for an older playseat evolution which had a bad design flaw in which the pedal stand would wobble due to the fact it was only attached at one point. This is a simple shim which remedies the problem. I printed in pla (sideways) with 10%...
thingiverse
... Pedals delivered e.g. ...with the Fantatec GT DD Pro. For mounting on the PlaySeat Challenge. ... Material List: 2 M6 * 30 mm screws (for the front clamps) 8 M4 * 20 mm socket head screws 8 M4 Nuts 2 M5 * 16 mm screws 2 M5 Nuts 2 Washers for M5
thingiverse
I needed to mount 2 transducers to my Playseat evolution and couldn't find anything anywhere, so i remixed another mount system to fit the strut bars that run under the Playseat, the vibration is incredibly lifelike. ...(Excuse the poor qualit print, it...
thingiverse
... two m3x25-30 screws and nuts. Two brackets hold very well the Fanatec shifter, if you add handbrake additional bottom support is needed - working on that one. ...Printed in 60% and 5 layers for bottom top and walls produced very sturdy brackets.
thingiverse
I needed something to mount Fanatec V3s pedals on Playseat Challenge, so I came up with this design. I've printed this in PLA, but you could go with PETG for strength There are 2 variants, one for M8 bolt since v3's has 8,5mm holes for mounting...
prusaprinters
I needed something to mount Fanatec V3s pedals on Playseat Challenge, so I came up with this design. I've printed this in PLA, but you could go with PETG for strength There are 2 variants, one for M8 bolt since v3's has 8,5mm holes for mounting and...
thingiverse
Installation: ========= * Install rear mounts (remixed part) with the 16 mm bolt in the hex hole on the mount and washer and nut * Install front mounts (original part) with the 30 mm bolt in the hex hole on the mount, use the included Fanatec Hard...
prusaprinters
5 layers were too thick for my chair so I lovered it in Cura to 2 layers and now it fitted perfectly snuggly. Tpu is used for better grip and for protection of a Playseat. Upper hinges are designed for an M6 bolt instead for M5 t-nut that comes...
thingiverse
- Tpu is used for better grip and for protection of a Playseat. - Upper hinges are designed for an M6 bolt instead for M5 t-nut that comes originally with SQ shifter. Insert M6 nut in "m6_t_nut_bracket.stl" and slide it instead of M5 in the...
thingiverse
This is a Logitech G27 Shifter suitable for Playseat Evolution. <b>It is important that the support is printed as shown in the cover image.</b> <h1>You will need:</h1> - 2 x M8 screws - 2 x M8 washers - 2 x M6 screws - 2 x M6 washers <b>...
thingiverse
I couldn't find any right-handed mounts for the Fanatec Clubsport shifter on a Playseat Challenge so I designed this. ...In addition to the prints, you'll need: 3x - 1/4"-20 nuts 3x - 3/4" 1/4"-20 bolts/machine screws 4x - M6x~18mm bolts/machine...
thingiverse
# Universal Playseat Challenge Fanatec Pedals Mounts After breaking the existing pedal mounts I found on Thingiverse I decided to design my own that would both be more durable and more versatile. This universal mount allows you to affix both Fanatec...
thingiverse
Recently purchased the Fanatec CSL DD Wheel & CSL Pedals combo intending to mount on my Playseat Challenge. The wheelbase mounted fine, but the pedals had no good way to mount rigidly other than the large velcro strap that comes with the Playseat. ...
prusaprinters
Universal Playseat Challenge Fanatec Pedals MountsAfter breaking the existing pedal mounts I found on Thingiverse I decided to design my own that would both be more durable and more versatile. ...This universal mount allows you to affix both Fanatec V3...
thingiverse
Be warned - You take sole responsibility for any damage to your Fanatec Shifter, Playseat Challenge chair, 3D printer and anything else by using this design. I won't take any responsibility for this home-made design! ... In the unlikely event of anyone...
cgtrader
Playseat Evolution Alcantara Pro Racing Simulator Seat 3D Model
thingiverse
Print 4 x Mounts Add 4 x M6x20 Hex screw 4 x M6 Locking Nut 8 x 6,4mm washer 8 x Cable Tie 4,8mm
thingiverse
Created this so you do not have to print so many parts. Use the 2 hinges from the original design. ... I'm using this construction for a while now and it works very well and stable.
prusaprinters
<p>I hate printing and removing supports. Here, i've blanked unsupported holes 0.2mm thick so you woulndn't have to.<br>Just punch through or remove them with something sharp after it's printed. ...No other changes made.</p><p>I'm unsure what license...
cults3d
It is a sculpture that shows the evolution of the human being, from the beginnings to the modern age.
thingiverse
This is a two color print showing the evolution of the 3D printer and the computer geek. ...
thingiverse
A set of mounts designed to rigidly mount the Fanatec Clubsport V3 pedals to the Playseat Challenge. May also fit other pedal sets. ... More Information:...