plutonium 3d model

**Update October 26, 2017:** Since I was messing around with the model anyway, I figured it was time to do something I've wanted to do for a while. To decrease the "stack height" on top of my inexpensive flexy tripod, I slapped an 18.5mm ball clamp...

Add one if you have adhesion problems.Dimensions and Part NumberingYou find models for many combinations of heights and depths. The heights are in the range 35mm – 100mm and the depths are in the range 80mm – 190mm.</p><p>These numbers are included...

It will not fit a full sized stepper, use their model if you have the original stepper motor. I suggest printing with the end that hooks over the carriage on the bed with supports on bed only. There are minimal supports this way and the hook keeps...

Until very recently, I never got around to actually writing any documentation describing this idea or doing any model of this bearing concept. I only toyed with the concept in my mind for a while back then and put it on the back burner until...

[Medium Sized Model - 25mm Base] [Presupported with LYS files in 32mm & 75mm Scale]   Among the first risen humans in Draksborne, Violet thought herself to be insane for her first life upon Tharador. For when she woke she remembered all that had...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_pattern_element_overlap = 0 custom_back_extra_port_corner_radius = 5 printer_tolerance = 0.4 stencil_pattern_element_radius = 6...

The left adapter does require a small alteration which I did with a pair of side cutters (the ones that came with my Ender 3) (see pictures): - Unscrew the four screws at the bottom (be careful these strip easily) - Gently pull back the white tabs...

Make the adjustments, render the desired  STLs and print it! The models are in the position, they should be printed. No support is needed. ...I suggest to use a 10mm brim for the tube to prevent it from detaching from the buildplate while printing this...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

Some of the models are difficult to hand-launched and should be tested with a 1/16" rubber band instead. A slight elevator-up reflex is required for flight. This is accomplished by latching the elevons up on the relex tabs on the aft end of the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

A hard case for your Eggtracker Mini to use with high power model rockets. Bill of materials: Eggtracker Mini (only tested with rev C3) Turnigy Nano-Tech Plus 300mAh 2s 70C Lipo Pack (hobbyking, amazon, search around and try not to get raped...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 6 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 stencil_pattern_line_thickness = 30 printer_tolerance = 0.4...

&nbsp;I am hacking stuff together in Tinkercad, so parts of the original Voron panel retention clips and hinges were used in creating these.I plan to make matching latches in the future, but for now am using these panel...

... to be retained and passed through, if desired. Can be nice if you want to completely remove the controllers from your hands at times without needing to set them down. Happy Printing. I would love to hear in the comments if you use this model.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8 custom_top_port_corner_radius...

About the Models Update: 24th September 2017 Added Y-splitter D6 8th September 2017 Added Multi Material for BLTouch 12 August 2017 Added Multi Material series 11th April 2017 Added Bowden series MM Parts and Y-Splitter I added the new MM parts just...

I first encountered the idea for this type of robot in a biomedical article, presented as a potential new candidate for exploring the human colon due to its simplicity and ability to navigate confined areas....

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

I've seen some Hedron models before, but none of them were quite right to me - they got the patterns wrong or just looked off in some way. So I set out to design my own, and this is the final result. Well, these are the final results because there...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

When properly positioned, the latches are ready to engage by sliding the wiring cover all the way to the right.\r\n\r\n###Parts List:\r\nAll links at Amazon:\r\n\r\nQty 2 required: 8X2mm...

Basic profile: 25% infill, 4 walls, ironing top layers, ...Note: the included images illustrate the goals of the steps outlined below.[ ] 3D Print included stl files[ ] sunlu_fan_mount.stl -- Mounts 50mm blower fan and thermistor to rear of fan...

:D This is a "small" and simple attempt to build a 3d printer. Small and simple are the keywords here. Just some basic parts to print, standard components you can get anywhere and no special and expensive tools required, as I don´t have access to a...

**HOW I PRINT MUCH QUICKER WITH STOCK HARDWARE** -------------------------------------------------------------------------------------- Here are the two videos that give details on how I print much faster with stock hardware (changes to slicer...

3D Printing: The Morse writer telegraph consists of many printed parts that are assembled together. Some of them could have been printed as a single piece. However, I avoided doing so to keep the printing times manageable. Additionally, this allows...

My goal was to make as many of the modifications as possible to be 3D printed parts.Note that in addition to the .STL files, the Fusion 360 file containing all these parts is also provided. Some parts need to be rotated after importing into the...

A round-pole design makes the assembly easier to handle and transport compared to square-shaped models.A horizontal T-mount platform is provided at the top of the tower for mounting customer-provided equipment. The tripod features a rotatable head...