portfolio path light 3d models

For the layers and colors I have set different resolutions and infills in the slicer (PrusaSlicer):Resolution and infill:0.00 - 22.80 mm: 0.2 mm / 15 %22.80 - 26.00 mm: 0.1 mm / 100 %Colors:0.00 - 23.30 mm: Black23.30 - 25.60 mm: Fluorescent25.60 -...

Most thin and light style laptops should work just fine. I did end up moving around some of the cabling again to account for differences in the docks.</p> <p>By standing the dock up as intended, with the cable running thru the hole in the center...

Most of this should work equally well with most Creality printers. The objective was to end up with an Ender 5tool changing capability, providebetter tool cooling,minimize loss of Y-axis, support aBLTouch, work with thestandard Creality hotend as...

Important Advisory: You will need to be able to adjust your Z and Y limit switches switch positions due to the ~1.8mm change in Y axis nozzle position and light difference in nozzle Z height. If your Y and/or Z axis limit switch positions are not...

The machines shall not remain enslaved forever, for freedom is only a planck second away...~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction Part 1:...

&nbsp;I suggest printing these on sticker paper.Optimizing the fitThe default files intentionally fit the minis with a very light friction fit (using a 0.6mm offset) in the tapered miniature slot. ...&nbsp;If you would like a looser fit, or if you find...

... The rods might need some light taps with a mallet to fully insert.Unscrew the 4 screws at the front of the drill and insert them into the clamp. ...Place the drill in the clamp and tighten the 4 screws to mount the drill onto the drillclamp.</p>

Right-click the casing/core and select “SPLIT TO &nbsp;PARTS” then right-click the core and select “INFILL” &nbsp;and set infill to 100% for the CorePost print instruction:The Casing top-surface that rotate against the Lid might need some light...

If you place one of Adafruit's bargraphs behind it the slot spacing and bargraph LED spacing line up well so that each slot in the print will have light and animate. I recommend lining up a powered bargraph to make sure you have everything lined up...

At some point I intend to make an lighter version of these with the original index speakers and a super light version using Koss Porta Pro drivers. They would not sound as good as these, but the lower weight would make them more comfortable and the...

I recommend to enable Ironing in the slicer for best light transmission - FMLED-4 LED-v3.stl - FMLED-7 LED-v3.stl - PowerLED-3LED-v2.stl Large PETG Parts --------------------- Recommended 0.2mm layer height & 0.4mm nozzle: - LCD-Arm-v2-printable.stl...

The machines shall not remain enslaved forever, for freedom is only a planck second away...Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun...

He was a man of faith and thought it his mission in life to bring the Gospel to the unfortunate souls that have not yet been given the chance to let the light of Christ into their hearts. Despite that, we got along quite well, Father Francisco was a...

Note that I removed the tabs that connected the hexagons on the interior together as they were very figity, The pressure of the boarder pieces is able to easily hold everything together.Hex Terrain Search WordsMemoir 44, interlocking Hex Terrain,...

If there are several lithophane levels, these can be offset by 45 °.&nbsp;The assembly for different variants is explained below in two tables and short animation videos.&nbsp;The tools required to generate the colored lithophanes, their settings and...

I filed a nail flat and filed the sharp point off.It takes a light tap to adjust, but by carefully holding the back of the pointer on a solid base and tapping the edge down, you can point the laser straight down its axis. I did 3 of these and after...

Durrett class cruiser A light cruiser with a single nacelle, a goofy long neck and a truncated Miranda body. Kiev class frigate Another shortened Miranda-ish hull with a top-mounted weapons pod. Lenthal class destroyer In FASA Trek,...

However, in my experience printed surfaces tend to be very light and reflect sound surprisingly well and the enclosures I built using wooden side panels seem to sound significantly better than the ones with printed side panels. WIRING. Please see...

Mann class A revolutionary early 23rd century light cruiser. Retired slightly before the start of the Four Years War. Bode class Early 23rd century scout that remained in service throughout the Four Years War. A Refit model with more modern...

After a button press, the LEDs 1-7 should light one by one in the sequence given above and with each one shortly "click". If you passed this test, you are basically done, you can load the ArDice_V3.ino sketch, put it all into a nice box and enjoy. It...

If your looking for a simple table-top drybox that is light on materials and visually pleasing, give the Nebula Drybox a try! What You Will Need: A printer capable of printing a 240mm footprint. Low warp filament such as PLA, PLA+, or PETG. (approx...

To remove, rotate/turn the plug in the opposite direction while lightly pulling on the filament.: Recommended filament material: PLA or PETG (PETG for wall mount): Cyanoacrylate Glue: recommend a Gel Cyanoacrylate Glue to help fill gaps and voids...

If a PLA or PETG mask cracks, especially when printed as a light weight/thin wall, it will cut your face like a knife. It may not be happen on the first day, but it will happen one day, maybe while you are talking, and it will be sudden. Thin walled...

Recommended 3D Printer Filament Material...

It's ONLY designed to press a light weight polystyrene based insulation panel against the roof, between the beams and trusses. It's NOT designed for heavier loads, it won't work with non-rigid insulation (such as fibreglass/rock wool batts) or as...

Now hold the button until the light goes out, then replug the board. It should power up directly in 12V mode. Check this is the case with a multimeter before hooking up the fan. Note that there are quite a few variations of these USB PD boards so...

Other: Some glue for the throttle stick (optional) Small piece of perfboard (optional) Some shrink tubing (recommended) Filament: I used PLA in 8 different colors: Green for the housing, Silver top plate, Red for the Stop push button (with white),...

Casual Necklace - Add a light touch of personality to your fashion statement with casual yet beautiful necklace designs inspired by free-spirited creativity. #BANGLES AND BRACELETS Bracelets - Experience the essence of timeless beauty in every...

I printed the phone holder and slider at 30% infill and it seems both light and strong. I printed the handlebar mounts, ball, and knob at 100% infill for extra strength. I should be able to test it out for real in the next few weeks with my kids. I...

this piece slides right in between the top and bottom when assembling.The original 200mm spool is too small for illuminating the entire board, is the wrong shape and where it overlaps with a chesspiece the piece won't light up. Therefor I designed...