power raspberry pi from ender 3 3d models

- Cable path for screen, Z limit, pi power/ethernet - Fan placement - Raspberry Pi power button (using OnOff Shim) - SD slot - Indicator lights Printed left side at .32 with no supports and came out great. Had stepper driver mishap necessitated...

A case designed for the original Ender 3 a Raspberry Pi 4B and a 3.5" TFT screen that connects via the GPIO pins. It also comes with a holder for the stylus that comes with most of these screens. ...The holder snaps onto the stylus and holds it...

A case designed for the original Ender 3 a Raspberry Pi 4B and a 3.5" TFT screen that connects via the GPIO pins. It also comes with a holder for the stylus that comes with most of these screens. The holder snaps onto the stylus and holds it...

Another remix of a Creality Ender 3 Raspberry Pi mount. Instead of relying on friction, four M2.3 6mm self-tapping screws screw the Pi in place. The snap-on face plate is off. To accommodate heatsinks, the case is higher than the source project. As a...

This is a closure for Raspberry Pi 3 and Ender 3 Screen. I fixed heat issues running my Pi and the Ender display by adding a 30mm fan to the box. Pi used -...

This is a remix from "Ender 3 Touchscreen Case & Holder for Raspberry Pi" by Tronnic. (https://www.thingiverse.com/thing:3030160) I used this to replace Ender 3 V2 stock display to raspberry pi display for Klipper firmware. Differences from...

This might work for other similar screens that use HDMI but I'm not sure, you will have to try it out.This was also designed for the Raspberry Pi 4B, other Raspberry Pi models have different port arrangements/locations so you will have to modify the...

Remixed from ‘Creality Ender 3 Pro - Raspberry Pi 2/3/4 + LCD Enclosure’ by eoyilmaz, specifically v042 for Pi 2/3. Note: **This remix only works for Pi 2/3**, not 4. The original is a really beautiful design. To suit my Pi 3B setup this remix...

Raspberry pi 3B+ case with built in camera attachment for my CR6-SE also should be compatible with the ender 3 There's a million octoprint set-ups out there but I wanted something that took advantage of the z space available on the cr6-se This is a...

This modifies [giacomo30196](https://www.thingiverse.com/giacomo30196)'s [Ender 3 Raspberry Pi 2/3 mount (UPDATED V2)](https://www.thingiverse.com/thing:3016364) rear/lower part to add a hole for a heatsink on the bottom of your Raspberry Pi. I had...

A compact Raspberry Pi 3 B case consists of three parts, including an extender arm specifically designed for the Pi camera v2, which can be installed on top of an Ender 3 Pro. This setup provides a clear top-view angle of the printing bed. The...

New version: June 24th, 2019 * Updated dimensions for USB and SD card opening in SKR case based on new model launched yesterday by user towe: https://www.thingiverse.com/thing:3701548 * Added small cutout inside SKR case for part of SD card reader...

Currently, this project requires: 12x M3x10 bolts (longer is fine, just be mindful that they don't touch the electronics), 2x M5x8 bolts (again, longer is okay), and 8x M3x5 bolts to mount the mainboard and Pi. ...If you're low on bolts, I think two...

Replaces "Front.stl" from https://www.thingiverse.com/thing:3294512/files The original version doesn't fit the Raspberry Pi Camera Module 3. ... This version makes the hole for the lens slightly bigger, and makes a little more space for the connector...

(So only the Raspi Case is untouched in this update) Version: June 11, 2019 A back mounted Control Case for your SKR 1.1 or 1.3 board with Raspberry Pi and LM2596 buck convertor on your Ender 3 PRO. Note that this was requested by someone else and...

Remixed this to work with the new Raspberry Pi Camera Module 3. ... Remixed RossIRL's Arm and Joint design as well as a design I found on printables by DocWeebl (https://www.printables.com/model/368788-raspberry-pi-camera-mount-camera-module-3-version.)

**SIDEBOX FOR MKS GEN V1.4 + RASPBERRY PI WITH 5" DISPLAY FOR USAGE TOGETHER OR EACH SINGLE, ATTACHABLE TO THE ENDER 3** HOUSING FOR PI IS FOLDABLE AND HAS A SLOT FOR THE PI-CAMERA-CABLE AT THE RIGHT PLACE FOR MOUNTING THE CAM AT THE X-AXIS. IT HAS...

This is a tray I designed to hold the Raspberry Pi 3B+ case from Canakit. You just set the case into the tray and there is enough clearance for all the I/O allowed by the case. Holds the case place well but remains easy enough to remove if...

This remix repositions the standoff and I/O cutout to allow the mounting of a Raspberry pi 3 a+. Use 4-40 screws to mount. ...For best results print with supports on touching build plate at 60 degree overhang.

... to the inside right frame upright. UPDATE December 31, 2018 I have added an extension to hold a Raspberry PI 3 B+. I have also added a frame mount point above the Raspberry PI. I corrected the hardware needed. ... ORIGINAL POST DATE August 9, 2018

UPDATE 31-Dec-2018 Added an extension to hold a Raspberry PI 3 B+ Added frame mount point above the Raspberry PI Corrected hardware needed ORIGINAL POST DATE 09-AUG-2018 Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 Infill:...

Ender 3 Pro enclosure for a Raspberry Pi 4 and a BIGTREETECH TFT35 E3 V3.0

Box for Raspberry Pi A + with support for the noctua 40mm fan

This is a custom Raspberry Pi 3 + Camera Mount specifically designed for the Ender 3 printer. Since I couldn't find any suitable solutions that met my needs, I took matters into my own hands and created one. The design boasts several benefits: Most...

Raspberry Pi 3 enclosure featuring an exposed LEDdar One sensor, accessible via a single Ethernet port and power input, designed specifically for silo monitoring applications where a minimalist approach is essential to streamline functionality and...

Hi this is a remix of the Ender 5 Raspberry Pi Camera Case - End Stop Mount model, modified slightly to fit the official Raspberry Pi Camera Module 3.

... components: 1. The Raspberry Pi 3 model, utilized in conjunction with Octoprint. 2. A 5-volt buck converter, responsible for powering both the Raspberry Pi 3 and a servo motor. ... This design has been optimized for use with Anet A6 3D printers.

A complete mod for the Ender 3 with SKR 1.3/ MKS 1.4 Raspberry Pi, a relay, an y chain, squashball feet and a drawer for tools and stuff. The grid ist printed with zero top and bottom layers and 50% tri-hexagon infill. The camera parts are...

- +10 mm taller (z) - (allows for 15mm fan installed inside case, with stepper driver heatsinks) - 20x10mm cutout at bottom for LCD ribbon cable(s) - (assuming you use longer ribbon cables) Changes to the left (Raspberry Pi) case: - 5 mm higher...

Raspberry Pi Enthusiasts Rally Behind Pi 3.