primary arms acss raptor 1 6 ffp scope throw lever by 3d models

It was designed to fit the Primary Arms ACSS Raptor 1-6 FFP Scope perfectly without any scaling required, even when printing with ABS material. I printed the part at 100% infill and then used sandpaper to carefully round all the edges before giving...

No supports needed for anything but you can use it on the lever for the screw and nut holes. Just snug tight, no need to crank on it. I printed the lever at 100% infill with carbon fiber petg. It's strong and matte black. The TPU was 20-30% no...

Cat tail lever for the Primary Arms 4-14x FFP scope prints with no supports required. Its chunky design is due to the extremely stiff zoom ring found in my PA 4-14x. This cat tail lever works seamlessly on both non-illuminated and illuminated...

I'm still waiting on my chance to try out the screw hole design, but I've included it just in case - and thankfully, the file without the hole has held up surprisingly well through a few range trips so far. ...Still, as with any first prototype, there's...

Primary Arms Scope Throw LeverSLx6 Silver Series 1-6"Beefy" to last awhileRecommend course screw of appropriate size and length.Starter hole provided, Predrill hole to avoid cracking.Will clear mid height scope rings in higher. ... Probably won't work...

Throw lever for Primary Arms 1-6x SFP scopes. This is an original design. **TABLE OF CONTENTS** - Parts - Printing Details **PARTS** - (1) M3x12mm socket head screw - (1) M3 nut **PRINTING DETAILS** - Settings (Tested on ender 3V2 with 0.6mm...

Re-mix from the throw lever by jitblass. I fixed the messed up geometry, beveled the edges (so you don't have to sand them afterwards), and shrunk the cutout for the nut to accept standard M3 nuts. Once printed, you'll need a M3 x 10 screw and...

Zoom in on the lever for the Vortex Diamondback Tactical 6-24x50 FFP rifle scope. It likely works with other Vortex scopes as well. I revamped a modified zoom throw lever design by NJ_v_N and made some tweaks to it. ...I added a threaded insert that's...

Zoom throw lever for Vortex Diamondback Tactical 6-24x50 FFP Probably works with some other Vortex scopes. I redesigned a bit the zoom throw lever by NJ_v_N. Added 3mm threaded insert, elongated the lever. Print Settings Printer: Printo3D i3 clone...

Athlon Scope Throw Lever for the Argos 6-24x50 scope.

Primary Arms throw lever. 2.5-10x. ... Will need nut+ screw

This is a simple throw lever for the Monstrum G3 6-24 Scope. ... All you will need is m3 bolt and nut to install it.

The Cat Tail Lever attachment is designed to complement the Optisan Mamba 1-4x scope, which had a limited release a couple of years back. ...This custom component was 3D printed without any support structures.

To do my own throw lever I used "Primary Arms 4-14x FFP Scope (1st gen)" from PoniesWhee because its quite minimalistic and I like how it look. I made some changes inside the lever to fit ring correctly, and also change a little scale to keep it...

To create my own throw lever, I drew inspiration from the Primary Arms 4-14x FFP Scope (1st gen) by PoniesWhee, which boasts a sleek and minimalist design that I really like. Inside the lever, I made some adjustments to ensure it fits snugly with...

... with a 3/8 inch hex nut to generate the necessary tension. ...The chosen screw should be exactly 7/8 inches in length; one option is to employ a longer screw, such as one that measures 1 inch in length, and then trim it down to meet specifications.

This is a scope ring lever for the Monstrum G3 1-3x24 FFP scope. ... It is deliberately a very tight fit, and will require patience and mechanical persuasion to install.

You can customize various aspects of the throw lever design, including its length, clamp position, scope notch angle, and depth. The best part is that all you need to do is install Fusion360 and figure out how to load the step file - not rocket...

scope throw lever for Leupold Rifleman 3-9x40 designed to fit over a 36.2mm adjuster. I used a M3x8mm bolt, but you could probably use a 5mm I added two M3 washers in the gap to prevent over tightening the ring two edges would not take a...

Insert the nut into the cavity of the Scope Throw Lever for Vortex Viper PST Gen I, then grind off any excess material with a precision tool. ...Next, cut the M2.5 screw to the precise length required using a high-quality cutting instrument.

You can customize everything from the length of the throw lever, to the position of the clamp to the angle and depth of the scope notch. Best part is all you need to do is install Fusion360 and figure out how to load the step file. (not rocket...

Extended lever for UUQ 3-9x rifle scope from Amazon. Zoom adjustment was hard to turn, and the regular lever was too small. ...This slides straight on the back of the scope, from the rear, for a tight fit over the adjustment wheel.

The Vortex Optics Viper PST 6-24 scope features a robust design and exceptional optical quality, making it an ideal choice for long-range shooting applications. ...On March 29, 2017, the addition of a detailed SketchUp model further enhances its appeal...

Quick zoom adjustment aid lever for shooting scopes. Lever made of PET, a more resistant printing material than usual. Files available from 38mm to 48mm. ... Accessories: 1 Allen screw M3x20, 1 Nut M3 If you want a diameter in articular let me know.

-------------------------------------------- This throw lever is modified for use with the Vortex Viper PST 1-6x24. It's made a bit tighter than usual, so attaching a vinyl tape to the scope when installing makes it easier to slide in and install...

scope throw lever for a Swarovski Z5 rifle scope. ... 2mm cap screw and nut required.

For Vortex Strike Eagle 1-8x24 scope, 45mm.

To fine-tune the positioning, align the component so that the throw ranges from approximately 10 to 2 o'clock. Next, slip the M3 nut onto the 10mm threaded rod and secure it by tightening until snugly in place. ...The hardware specification includes: M3...

I wanted a larger throw lever than what was available on my CVLIFE Scopes(https://a.co/d/29N7bz1). Let's the gun go into my cases. Uses M3 x 12mm Screw and nut. ... Added V2 which is thinner and more rounded for lower profile scopes.

It makes zooming IN/OUT much easier (even in gloves) :)Uploaded model (both versions) has these parameters:inner diameter: 46,0 mmI use this throw lever on my rifle scope Vector Optics Matiz 3-9x/50mm but it can be used for any other.If you need to...