print bed 3d models
1239267 3d models found related to print bed.thingiverse
Print Bed Scraper/Spatula that removes prints from your bed without scratching it!
thingiverse
These bed level adjusters allow you to easily level your print bed from the front of the machine.
thingiverse
You may need to place the STL diagonally if it does not fit on your print bed.
thingiverse
Instructions Use the Customizer to generate a print bed leveler for your print bed and layer height. If you have a Replicator (original) you can use the STL files attached here. Print it. The plastic should be the same color and width across the...
thingiverse
Print bed clips that don't snag the y-axis. Useful for bad warping issues using Nylon etc. ...Print using something like PETG or ideally Nylon.
prusaprinters
Suggest to print with 30% infill and 5 walls. ...You may need to place the STL diagonally if it does not fit on your print bed.
thingiverse
Created a storage solution for my Ultimaker 3 Print beds. Printed this with Carbon-Nylon filament at .1mm layer height at 50% infill. ...No Supports.
thingiverse
This is a scrapper for most print beds. ...Works great on the monoprice mini delta III and the New Matter Mod-T
thingiverse
I took the print bed handle http://www.thingiverse.com/thing:1858501 and widened it in the middle just to make it wider for my fat fingers.
thingiverse
a fixed version of the Print Bed Scraper I found here on Thingiverse. ... The original had a gap in the model
thingiverse
This object helps in the calibration of the center of your print bed. ... Its overall size is 30 mm x 30 mm x 2 mm in height.
prusaprinters
Print Bed SpacersTPU Spacers to replace the springs on your print bed.These are the standard size for an Ender 3 at 16mm & 18mm heightsTPU Shore hardness 95a.2 Layer height100% InfillNo supportsIf you like, like.Enjoy!
prusaprinters
The plastic should be the same color and width across the entire print bed.If the layer gets squished too thin and breaks up, lower that area of the print bed.If the layer is lighter, narrower or doesn't stick to the print bed at all, raise that area...
thingiverse
I found that the blue tape on my print bed was lifting at the edges and allowing my prints to warp on occasion, these clips are simply pushed over the edge of the print bed and they keep the blue tape firmly attached to the bed. To change the tape...
thingiverse
Adjuster for print bed, much easier to use than the wing nuts supplied with the tronxy. Fits 7mm nuts that are supplied with the printer. ... Updated adjuster has a deeper recess to bring the nut closer to the bed screw.
cults3d
GoPro mount for the Ultimaker2 print bed. Simply slides on and off. Great for documenting your printing progress. ... Added a version for the Dremel Ideal Builder as per a request.
pinshape
Created a storage solution for my Ultimaker 3 Print beds. Printed this with Carbon-Nylon filament at .1mm layer height at 50% infill. No Supports. ... No printer? Check me out at Feefer3D ***Subscribe to my Instagram and Facebook!***
thingiverse
Part for mounting a print bed, attaches to the corner between two 2020 aluminum extrusions. ...Printer: -- RigidBot Filaments: (full list can be found on thrinter.com) -- Hatchbox Transparent Black ABS -- Hatchbox Transparent Red ABS
prusaprinters
This object helps in the calibration of the center of your print bed. ...Its overall size is 30 mm x 30 mm x 2 mm in height.</p>
myminifactory
Part for mounting a print bed, attaches to the corner between two 2020 aluminum extrusions. ... Printer: -- RigidBot Filaments: (full list can be found on thrinter.com) -- Hatchbox Transparent Black ABS -- Hatchbox Transparent Red ABS
cults3d
Part for mounting a print bed, attaches to the corner between two 2020 aluminum extrusions. ... Printer: -- RigidBot Filaments: (full list can be found on thrinter.com) -- Hatchbox Transparent Black ABS -- Hatchbox Transparent Red ABS
thingiverse
That causes it to ignore the print bed perimeter settings. If you set bed size to X160mm Y160mm. The bed size of the Me Creator2. The carriage slams and skips. Any time you print something close to the limit of X 160mm. When you change the size to...
cults3d
There were concerns over the printed wingbolt hitting the aluminium extrusion under the print bed when the mount is fitted to the print bed support. Use the key to wind the thread in and out then remove it. There should now be plenty of clearance...
myminifactory
There were concerns over the printed wingbolt hitting the aluminium extrusion under the print bed when the mount is fitted to the print bed support. Use the key to wind the thread in and out then remove it. There should now be plenty of clearance...
youmagine
There were concerns over the printed wingbolt hitting the aluminium extrusion under the print bed when the mount is fitted to the print bed support. Use the key to wind the thread in and out then remove it. There should now be plenty of clearance...
thingiverse
These spacers make the built in bed clamp level with the surface of the printer bed. ...This way your honeycomb can lay flat on the print bed, and you still have the option to use the bed clamp if you wish.
thingiverse
Print parameters: Material: PLA or PETG Layer high: 0.3 (Nozzle diameter 0.5) Infill: 50% Additional material used: 1x print bed spring (length 20mm) 1x M5x25 (as a shaft for wheels) 1x M5 hex net 1x M5 washer 1x M6x25 (as spring tension) 1x M3x16...