print display stands 3d models

My first X-carve project (other than making my own top spoil board): Designed a display stand for the x-carve in Fusion360. If I were to build another one of these, I'd double the extension arm width (just put two arms together back-to-back) for...

My Wife was tired of looking at her ammonite Fossil Flat on the surface and wanted a stand to display it better.  I wanted it to be delicate and get out of the way so after the first one was not strong enough I modified to a 2 MM by 3 MM posts and...

360 rotating display stand/plate, with microwave plate motor. As a motor I used that of a microwave (turntable), it must be powered at 220V without a controller, every time it is powered it changes the direction of rotation randomly, while for the...

Similar to my other Nintendo hand held display stands. This one does require some additional small dowels to actually hold the DSi XL by the screw holes next to the cart slot. I just used a 3mm wooden dowel that was cut into two 10mm lengths. You can...

The collection of **LEGO Speed Champion** cars is growing, and I needed to come up with an idea to be able to place them all on the same shelf for display. There are different base plates for different cars, therefor I've designed different...

It requires two arms per base, which means you'll need to print three separate models to complete the stand. If you're interested in purchasing one, my Etsy shop can be found at telltaleatheist.com/3dstore. I typically print these stands in black and...

Nach dem drucken einfach beide Teile zusammen kleben und das hält ;) This is a remix of the mini 2 stand for the Mavic Pro. I split it into 2 files because it is easier to print that way. ...After printing, simply glue both parts together and that will...

Nach dem drucken einfach beide Teile zusammen kleben und das hält ;) --------------------------------------------------------------------------------------------------------------------------- This is a remix of the mini 2 stand for the Mavic Pro. I...

Here is an Ornament Display Stand that I created using my Glowforge Laser Cutter. This design features slotted stands tailored for two thicknesses of plywood: 0.13" (Glowforge Medium Plywood) and 0.23" (Glowforge Thick Plywood). The entire sheet of...

The main design requirement was to pack as flat as possible to ensure ease of transport and minimal shipping costs, as well as having the option to store the stand away during summer when the winter helmets are not in stock.Material expense and...

The main design requirement was to pack as flat as possible to ensure ease of transport and minimal shipping costs, as well as having the option to store the stand away during summer when the winter helmets are not in stock.Material expense and...

Table top display stand for multiple art prints in a gallery or farmers market. Sample shows an 8" X 10" Matted Print in the stand. ...Print Settings Rafts: No Supports: No Infill: 5% Category: Art

Engineered with single-color printers in mind, these stands can be assembled in multi-color while being printed on a single-color printer! These stands offer a sleek and stylish solution for organizing and displaying your controllers. With their...

... New project: this time is it watch display. This simply design can look great on your night table or office desk. You can always print more piece and stack one another one. ...Watch holder is removable then you can easy place your watch on holder.

... ...The Stand can be printed as is, and the kit is in 3 parts, Left, Right and Connecting bar, and it's held together with 2x 10-32 Nuts, and 2x ½" 10-32 Screw.Hammer the 10-32 Nut in the side of the Legs and screw the connector bar from the bottom.

Its design is meant to resemble the BAC (British Aircraft Corporation) Logo, since Coby did the British Airways Version.I did print it like this ones and I find the angle in which the Concorde is rolled sideways a little too aggresive. And the studs...

Unfortunately, the initial stand didn't meet my expectations - it had been designed after an old ceramic-style stand that I had spotted somewhere. This is where my new prototype comes in; you might need to adjust your print settings due to its narrow...

... ...The Stand can be printed as is, and the kit is in 3 parts, Left, Right and Connecting bar, and it's held together with 2x 10-32 Nuts, and 2x ½" 10-32 Screw.Hammer the 10-32 Nut in the side of the Legs and screw the connector bar from the bottom.

Lighter display with capacity for 44 Clipper lighters distributed on two floors. ...Comfortable and elegant Lighter display with capacity for 44 Clipper lighters distributed on two floors. ...Comfortable and elegant

laser cut switch display for games. ... 3mm clear acrylic

Display for the mythical Nokia N-Gage cell phone.

Simple yet stylish V-Pet display. ...Holds 4 V-Pets.

A sleek display pedestal proudly showcases up to five of your prized Nintendo Switch game cartridges on full display.

Simple Zippo stand for 4 lighters

... adjust it accordingly (100/150 = 0.667). I added extra thickness to the sides of the "seat" since the drawing was too thin for printing, as shown in my print's photos. ...Please check the recommended print settings for your specific printer model.

... recessed circles to help with placement of stick-on foot pads. I like to use them, but I hate it when I don't get them symmetrically applied. For a smoother print, I printed the Bed on it's side, with supports for the hole the Stand slots into.

(https://www.myminifactory.com/users/LazyBear3D?show=tribe) New project: this time is it watch display. This simply design can look great on your night table or office desk. You can always print more piece and stack one another one. ...Watch holder is...

I'm designing a simple necklace display because I couldn't find anything that caught my eye previously. It has a relatively flat design, so you may want to modify it if you prefer a more dramatic angle. The front section requires additional...

... I printed the clip on its side with some small tree supports for the slot. It could be printed upright but the layers would be in the same direction as the sheering force from the weight of the model which could cause a failure at some point.

The plaques hold a 50p in place with out any glue, although your print may need some tweaking depending on your printer/settings. Print instructionsCategory: Coins & Badges Summary This is a stand for my collection of UK 50 Pence coins. Each...