printrbot simple 1405 3d models
269450 3d models found related to printrbot simple 1405.thingiverse
Print 4 and put them under your Printrbot Simple 1405! ... (123D Autocad file is included in the downloads section) CHANGELOG V1) Initial model V2) Fixed a problem where some slicing engines would not render a face
thingiverse
Feet for the Printrbot Simple 1405 - two front feet that bolt on using the 1405's existing screw holes, and a rear foot that press-fits into place. I wanted to use TheSoup's excellent 1405 support feet, but the rear foot wouldn't work while my...
thingiverse
This custom Bowden conversion can be printed on the Printrbot Simple 1405 (though mine has been upgraded already). By replacing the extruder with a 3D printed hot end mount, it is possible to increase the performance of a budget printer like the...
thingiverse
Fan duct for the Printrbot Simple 1405 edition. This replaces the two wooden fan mount tabs and provides much better air flow than the printable fan shroud uploaded by Printrbot. This part also provides stabilization for the extruder motor and adds...
thingiverse
Instructions They can all fit on the Printrbot simple print bed, although you have to make sure the back leg is at a 45 degree angle since it's slightly longer than 4 inches. I printed two front legs and had them on both sides of the printer. You...
thingiverse
Note that I have a fair amount of ventilation here but my printrbot has a fan so if you don't have a fan mounted on the front you may want to consider doing so when adding this bottom since you will be reducing airflow. ... The fan mount I used can be...
thingiverse
Work in progress Upgrade your Printrbot Simple 1405 with this 10mm Z upgrade. ... Standard 3d parts used
thingiverse
This simple part zip ties onto the existing pieces for an extended x axis on a printrbot simple 1405 to stabilize the printbed. ...The incredible expanded x axis mod can be found at http://www.thingiverse.com/thing:383713/#files
cults3d
This is a printable STL file fan mount that can be mounted to the front of the Printrbot Simple 1405 to keep the extruder tube and head cool to prevent filament jams.
thingiverse
A fan mount that I made to go with the E3D Lite6 hotend for the printrbot simple 1405. I have also added the custom mount I use for mounting the E3D Lite Hotend, it could be improved upon. update: added thicker fan shroud. ...Print Settings Printer...
thingiverse
Unfortunately the designed was too big to print on the Printrbot Simple 1405 XL (because of the 100mm Y axis max) so we printed it on our Replicator 2 but it should print on a Metal Printrbot Simple. SketchUp file included for your convenience. ... ...
thingiverse
Here is the Printrbot Simple 1405 dual hotend mount. This is designed for use with Bowden setups like the E3D. This part mounts to Jon Lawrence's Y modification. I don't currently have a second E3D so this will be a WIP until someone uses it...
thingiverse
We recently upgraded our Printrbot Simple 1405 to the XL version. Our printer was printing perfectly prior to the upgrade but after the upgrade we noticed that there was a lot of inconsistency in the Z direction (layers) of the prints (see image). We...
thingiverse
This is a printable STL file fan mount that can be mounted to the front of the Printrbot Simple 1405 to keep the extruder tube and head cool to prevent filament jams. Instructions This mount is designed to accommodate two 40mm fans (I bought mine...
thingiverse
Well, the Printrbot Simple 1405 model doesn't seem to come with any way to contain the wires inside, so I made a cover piece to do so for mine to make it a bit tidier and thought I'd share it. It's meant for the 1405 model but it may fit other models...
thingiverse
... at .2mm layer height. I just found out Printrbot actually makes a fan shroud for the Simple 1405. I wish I would have known that 5 hours ago. :P Here is the link if you prefer that one. They look very similar. ...printrbot.com/project/simple-makers/
thingiverse
Work in progress of fan shroud for the old simple 1405, have to print it and test fit, but it should work
thingiverse
With the printrbot 1405 maker's edition, I don't know if I missed something or not, but the Fan Shroud they linked to in the instructions was for the wrong kind of printer. It was for the Printrbot metal, and didn't fit on the Simple. I couldn't find...
thingiverse
This allows you to clamp your Simple 1405 to the table top instead of screwing it down or letting it walk all over as it prints. I also included a cut-down version that will print in the 100x100 area of the standard printer. ...
youmagine
Identify the bolts on your printrbot that line up with the holes in the printed parts for the four side arms. For one arm at a time, slightly over tighten these bolts then unscrew. use the same bolts to attach the printed arm. They should be just...
thingiverse
Had a hard time finding good dampener for 1405 so designed my own. For best results print sideways with raft enabled. First self modeled 3D print. Made adjustments for .5 mm in wood thickness if tolerance isn't completely correct adjust scale in...
thingiverse
I made these belt guides to keep them from slipping off of the Printrbot's 624 bearings. Especially helpful if you're using longer belts (like for the XL bed), or if your bearings aren't exactly aligned. Both print very quickly, but I'm only...
thingiverse
I couldn't find one that was for a webcam and my simple so i created one. My webcam is a Logitech Quickcam E3500 which has a pivot mount. I designed a part of that mount onto this so that my webcam can still pivot.I made it in two part to keep the...
thingiverse
This is for the 1405 version of the Printrbot Simple. ... Please see source for more info.
thingiverse
Piece that is used to adjust the Y-axis tension belt on the Printrbot Simple Makers Kit (1405) This part was designed so that you wouldn't need to hold the nut while adjusting the tension of belt for the Y-axis. I think it makes more sense for the...
thingiverse
This was specifically designed for the 1405 simple because of the Z rod spacing, but if someone can give me the measurements for the other Simples out there I will happily modify it. These parts should not require any modification to be done to your...
thingiverse
... to around 65mm. Good for 3mm or 1.75mm filament, depending on what you use on your 1405. NOTE: This will work on ANY 1405 with stock Z rod spacing! That means the wood Simple or Jon's fully printed one. ...This is a MUST for direct drive bots!
thingiverse
... Instructions Retourner le support 1 de (-90°) sur l'axe "X". Imprimable avec Printrbot 1405 Origine 85 x 85 x 100mm max. ...Impression 50% infill, PLA
thingiverse
I borrowed the clawfoot design ( https://tinkercad.com/things/2x5aMtWwHrW )and modified it to fit the Printrbot 1405. Simply print 4 of these out and remove the back supports. I painted mine (yes its a bit sloppy) with fingernail polish. Slap 2 on...
thingiverse
This is a Bata STL file for a dual extuder plate for the new Printrbot Simple makers kit. ...3/8" BSP connections Please Test and post with results :)