prusa spool holder 3d models
405454 3d models found related to prusa spool holder.cults3d
HelloBee Prusa (Beeverycreative) - Spool Holder for Bq (older version) 1kg Filament, works for anothers brands too.
thingiverse
Part of "Prusing the RAISCUBE R2" project. ... Based on Prusa MK3 Spool Holder, the clip, have been redesigned to fit on RAISCUBE R2 Frame. ...
thingiverse
Extended Prusa i3 Spool holder. Can be used with WhamBam enclosure. ...May need to file down a little depending on printer tolerances.
thingiverse
... the dimensions are a bit larger. Rather than tossing the Prusa spool holder and printing a new TUSH spool holder, I opted to remix the parallel adapter, making it a little bit wider and a little bit longer so that the Prusa spool holder would fit.
thingiverse
HelloBee Prusa (Beeverycreative) - Spool Holder for Bq (older version) 1kg Filament, works for anothers brands too. ... Check ou more of my designs at https://cults3d.com/en/users/Albuquerque/creations
thingiverse
As in the original design, the Prusa Spool Holder uses: 8 M3-0.5x20mm Socket Cap Screws; 8 M3-0.5 Nylon Lock Nuts; 4 608 inline skate bearings. My initial print is in PLA and I will determine if I need to print in PETG later as I watch it perform...
prusaprinters
REMIXED PRUSA SPOOL HOLDER Print Settings Printer Brand: Prusa Printer: i3 MK3**Rafts:** No Supports: No**Resolution:** 200 Infill: 20% Triangle **Filament:** [...
prusaprinters
REMIX OF PRUSA SPOOL HOLDER DESIGN Print Settings Printer Brand: Prusa Printer: i3 MK3**Rafts:** No Supports: No**Resolution:** 200 Infill: 20% Triangle **Filament:** [...
prusaprinters
In this photo, the spool rides the bearings but can use the original holder if needed, however I have not experienced stability problems with my use of this design.As in the original Devilscave design, the Prusa Spool Holder uses:8 M3-0.5x20mm...
thingiverse
PRUSA SPOOL HOLDER B4 FILAMENT GUIDE. ... simple, small, fast print Filament guide for Prusa B4 holder
thingiverse
[For details and most recent files please see PrusaPrinters.org](https://www.prusaprinters.org/prints/61710-prusa-spool-holder-with-bearings)
myminifactory
I made a little clip to hang my Prusa MK3 spool holder on an IKEA Skadis board when I am using other spool holders.
thingiverse
My attempt to get it rolling easier to my Prusa mmu2s spool holder. Found no easy solution so I drew this. Keep it simple. Significant difference and now it works much better. ... 2 of each / spool holder axel
thingiverse
This is a squashed Bug to use your one-piece Prusa spool holder as a Table Spool holder. I had a dual spool holder with my Mk3 so I could justify making this over seperate spool holders. My settings with PLA: Layer 0.2 mm 60% infill cubic ...
thingiverse
... appropriate for your enclosure top. You can screw it down right up against or very near the slot cover. The spool holder interface part is removable, just snap it onto the Prusa Spool Holder and slide it into the grove on the mounting block.
thingiverse
I used the Prusa Spool Holder and Modified and created this holder to mount onto an IKEA Lack table. It fits snug and can either be secured with 3M Tape or I have included two screw holes on the bottom to drill into the table. There is a Left and...
prusaprinters
I remixed this centering sleeve from Michal Fanta's Gravity Spool Holder, to fit over the Original Prusa MK3S(+) Spool Holder and to stop spools from rocking during printing. You can use the (orange) nuts from Michal Fanta's design or the Gravity...
prusaprinters
This may require some force, but the pins should slide in just fine.You are done, great!Attach the base part to the Prusa spool holder using the screwdriver before you attach the threaded rod, otherwise it's going to be a bit difficult ;)See the...
thingiverse
This Spool Holder can replace the stock spool part that comes with the Original PRUSA MK3 & MK3S.
thingiverse
A nice Spool Holder designed for prusa. ...I suggest to double the z scale before printing in order to get it thicker.
prusaprinters
This is a spool holder adapter for the Prusa MK3 injection molded spool holder. It allows you to use spools with smaller diameter bores on the Prusa.This prints in 3 separate pieces and then fits together. ...Add glue during assembly.</p><p>I included a...
thingiverse
This is a spool holder adapter for the Prusa injection molded spool holder. It allows you to use spools with smaller diameter bores on the Prusa. I own a few MK3's and a Dremel 3D45 so it's nice to be able to mount the Dremel spools when needed. ...
prusaprinters
This is a spool holder for a Prusa i3 that will hold a 1/2 to 3/4 dowel or pipe allowing you to add another spool as well as easily changing spools without removing the arms. I used a piece of PEX piping. It should make it easier to change the spools...
prusaprinters
...When I received my bulk filament spool, I had no way to print with it, so I needed to make my spool holder capable of holding the 4 KG spool from 3D Fuel. New spool extensions are the khaki color, and replaced the black pieces shown in last picture.
thingiverse
Most of the filament spools I have are 20 cm diameter, but I designed the holder so you can move one of the rod in if you have a smaller spool. It takes spools up to 100mm wide. Note that there are different set of the holders. One named 5_5mm that...
thingiverse
Instructions To assemble this spool holder, you'll need the following parts/hardware: -Four printed bearing guides -Four printed bar clamps -Two 130mm lengths of m8 threaded rod -Twelve m8 nuts -Sixteen m8 washers -Four 608zz bearings You just need...
thingiverse
This is a spool holder that uses the original holder that comes with the Prusa I3 MK3S I designed this because I did not want to drill extra holes in my wall. The part are bolt on and do not require any tools except for an allen key. The original...
thingiverse
Mk1 spool holder for several dimensions of spool. ... Suport for 2kg spool with filament guider half year tested distanz part is not reqired parts : printed parts 3x 112mm M8 threaded rods 10x M8 nuts 4x inline bearings