pvs14 eyepiece 3d models

The case enables the webcam module to be used not only for photography but also for astrophotography - you can simply unscrew the camera lens and insert the module into the 1.25" interface of the telescope, replacing the eyepiece in the process. It...

I also attached a parfocal ring to the laser collimator to give it a square shoulder (this helps when inserting it into the eyepiece holder on my telescope, but is strictly optional). The V-block jig keeps the laser collimator securely aligned...

The Suit is equipped with a Communication System - FACE MASK- that features advanced Optics for Visual Enhancement, incorporating highly Advanced Eyepieces designed to Protect the Eyes and enable Clear Sight even in Severe Space Environments. The...

Finally got around to putting up, amended mid section ,Weapon And SuckerSTL files marked with a 2 at the end.When assembling don't overdo the glues, on the socket topsAdded Grab claw as alternative to sucker1963 Early Dalek from Dr WhoThere is a one...

The ring fits over the microscope eyepiece and the flat plate provides a surface to rest the phone on to help stabilize it. ...It works well for my purposes and prints up quickly.</p><h3>Print Settings</h3><p><strong>Printer...

Moving or retracting the screws allows the tilt of the mirror support surface to be adjusted in two directions to properly align with the eyepiece. The main block includes two curved holes set at right angles, allowing two wires to be threaded...

It converts it for astrophotography, to be used with a telescope with standard 1.25" eyepiece. Compared to the others, it uses no glue or additional hardware, and is very easy to print without support. It also features an inner wall to shield the...

When the binoculars fell apart, one of the eyepieces actually rolled off the roof I was on and was not damaged in the fall, so I knew I had to fix it, if it can take that kind of abuse. This retaining nut is just held in place using a M3X10MM cap...

My own quick holder for my Galaxy S5 to attach to my 60x spotter scope - the eyepiece is 36mm diameter and this should slide right over. At the moment, I am attaching with rubber bands and the pegs I've put on the board - I'll try later to add a...

Next up: attaching the film to your newly created eyepieces. Easy does it; just glue them on and you're golden. Now we move onto the pièce de résistance – crafting the iconic loops that will frame your solar eclipse viewer's ears. Wrap a generous...

You have to fix the dryer with the eyepiece screws. Maybe it is 1-2 of a tenth mm to narrow Also the screw threat (M55) is not perfect. I can use only 1.5 turns. Maybe it is a problem of my printer settings. The Fusion360 design is ok. However...

The hole closest to the eyepiece end is the focus lock but must be attached for the focusser to function. For this I used a longish cap-head bolt. The metal plate doesn't rest on the screw head, I used a couple of washers either side to give a bit...

Instructions: Use These Settings to Customize Your Design: eyepiece Diameter = 2.5 Toes Angle Adjustment: Set it Between 80-0 Degrees Leg Spacing: Customize to Your Taste at 2 Ring Thickness Adjuster: Dial It Up to 3 Beak Separation Ratio Setting:...

... for where to place the wires or you have another reference picture besides this one please post it in the comments! Possible solutions include creating space for a button battery inside the eyepiece or running the wiring through the mask. ...^-^

... The eyepiece prints separately, but it can be adapted to fit any device with a ready-made case in STL format. This design features removable sighting profiles in two versions - photos and video - with different view angles depending on the format.

The original model also omitted the eyepiece rings and weapon wire bits -- but lets be honest, it's a paint roller. Those parts are included here. ### How to Print I highly recommend that you use a 0.2mm nozzle at your highest resolution height...

The 3d print files "lens", "eyepiece" and "union" I designed, you can print them with the parameters of your preference. The files for "Cell phone holder" were designed by someone else (https://www.thingiverse.com/thing:4599498). Joining everything...

The original model also omitted the eyepiece rings and weapon wire bits -- but lets be honest, it's a paint roller. Those parts are included here. How to Print I highly recommend that you use a 0.2mm nozzle at your highest resolution height for...

Release the thumbscrew securing the Head/Eyepiece Tube on your LOMO microscope, then insert the bottom portion of this 3D print into that space and attach it firmly, connecting your camera to start capturing images and adjusting its orientation as...

This resulted in corners being shaved off the eyepieces - a deliberate decision made for the final product. To bring this prop to life, you can print the three buttons in translucent plastic and then place LEDs behind them for an extra special...

This results in about 15mm more inward travel and a more secure fit for eyepieces. Now I can focus on objects in the night sky and take photos without using a barlow lens. The images are of the Orion Nebula and the Pleiades. Here's a link to...

This adapter is a universal smartphone / cell phone adapter / platform to use on the eyepiece of a Leica EZ4 stereo microscope. There are two parts to this design to allow for color coding different adapters by the ring portion of the design. You...

Mounts for compact digital cameras with sleek design and versatile applications, fitting snugly over 1 1/4-inch eyepieces. **Easy-to-Follow Instructions** Built entirely from high-quality ABS material for maximum durability and performance. Z Axis...

So, I removed cross-haired eyepiece side and make a male-to-male thread converter to connect T-threaded (M42/0.75) guide camera to the finder. This finder has rotating objective with thread to adjust focus, so don't need additional focuser but just...

The Nikon T adapter allows me to use any 1.25-inch Plössl eyepiece or filter. When I have time, I'll try to post links for everything used in this project. I included mounting holes to secure the Pi Cam with four bolts, but pressing it into place...

http://www.astrosurf.com/solex/sol-ex-objective-en.html The PhotonFy adapter allows the portable spectrometer to be used with a standard 1.25" or 31.75mm eyepiece output. It can be printed with a layer height of 0.15mm. ...For securing the...

The goal is to use Rpi Camera module with a 1.25" adapter or a 1.25" eyepiece or camera attached to it. I will attempt to create a star guiding system by assembling the focuser with a 50mm refractor telescope. If you have a different tube...

Two eyepieces provide magnification factors of 16 and 30, allowing for observation of moon craters and even the moons of Jupiter. ... Mirrors and lenses are available at: http://astromediashop.co.uk/Telescopes.html...

This endeavor aimed to repurpose as much of the original equipment as possible, including the eyepiece holder, focuser knobs, metal plate securing the focuser knobs against the rack, metal coverplate, two screws holding those pieces in place on the...

To make sure it fit perfectly, I modified the design by adding two eyepieces that would fit snugly over my glasses. I also removed the original straps and rivets so that I could use real ones instead. Since the mask was too small, I scaled it up a...