pyramid puzzle redrawn in openscad 3d models

No epoxy was used in my system. After 24 hours with a full water tank sitting on a paper towel there was no visible water leakage. Results may differ with different filament. The water pump adapter was created specifically measuring the Songlong...

In order to minimize post processing I made a two part design for the enclosure and cartridge so you won't need to print supports and post-processing will be minimal. For assembly instructions go to:...

Check it out in action on YouTube: https://youtu.be/V9su3MfrOe0 Bill of Materials: Qty 1 ($1-$33) Vacuum Tube 8 Pin (does not need to be operational) I used this burned-out tube from a tube amplifier, but any 8 pin vacuum tube should work after...

This module is useless on its own; it's designed for use in conjunction with a connector, such as the dovetailSpoolHolder below. Parameters: - length: Decimal value specifying cylinder length, set a bit higher than spool width for play. Default is...

This design can handle items as large as 50mm square, and the vice shown in the picture measures 4545 x 250mm. To complete the saw, you will need to source additional parts, including two 8mm steel rods (340mm long), two 6mm threaded rods (200mm...

  MotivationLike to have a nice cabinet for my mk3 (or any other 3D printer) to print ASA and Co. cheap, based on used stuffgood looking (very important)really heavy ~100 kg eachspace for printers up to 50 x 50 x 50 cmspace for many...

# BOM: Excludes power supply and sd card as they are very variable in price 4x 3mm x 10mm screws €1 2x 3mm x 20mm screws + nuts €1 4x 2.5mm nuts €1 2x small gauge wires to connect keyboard power €0,5 5x GPIO wires , not too small gauge for 5V €2...

60mm bases in Sector Mechanicus walkway design. If you like my work please consider supporting me on Patreon. Become a Patron! ... Some of my other designs: https://www.thingiverse.com/thing:4654378 - Rivet Cutting Tool...

Decide which mounting holes will be used in the base to attach the miter bar. You want the front of the base to be ~2" from the blade. 2. Insert 2 10mm hex nuts into the mounting holes you chose. These will fit very snugly. I threaded a bolt partway...

*Instructions available in german here: https://www.voss.earth/tonuino/* This enclosure has access to the SD-card, allowing me to swap the contents without having to open the case (and therefore being able to glue the case together for added...

... the momentary switch on top of the device. It will always tell the truth. Presentation When giving these devices as gifts, make sure to believe in them. ...Take on the role of artist, magician, or TV infomercial host and sell it with confidence!

Willpower is a force people often claim they need when starting a diet, training for fitness, or striving for a challenging goal - making significant changes in their daily habits. To create lasting change, one typically requires a considerable...

**JAPANESE MASK COLLECTION** myminifactory.com/users/bstar3Dart/collection/japanese-masks-collection Devil Mask - Hannya Mask - Samurai Mask for cosplay 3D format: STL file (If you need .OBJ format - You can contact to me) 2 version for print v1:...

Note how the eyes and toes are “masked out”Set fuzzy skin feature (right-click on modifier block; Add settings; Fuzzy Skin; Select all check-boxes; OK)Find the Fuzzy Skin box in the menue on the right (Part Settings to modify), choose Outside Walls...

The triangular rim and slot in the middle part of the joint are a little hard to clean (sorry) but the good news is they don't add any significant structural integrity to the assembled frame so if you clean them too much, you'll probably be okay...

Support My Channel So I Can Create More Awesome Projects, Thank You! Hello Friend! ...Visit My Website for Reviews and Links to Quality Hobby Products.</em></strong></h3> <h3 style="text-align: center;"><strong><a...

Without untwisting and interference in the middle of the equipment. When using, monitor the battery level.. the lower threshold is 3 volts WARNING!!!! Do not connect to the remote control without setting a maximum of 6 volts (the board will...

When installing the door magnet remember that they have to be in opposite polarities for the magnets to attract each other, otherwise they will repel each other. Parts links below: Double-sided Tape 50mm Neodymium Magnet 8mmx2mm See the video for...

A JIS 0 or PH 0 screwdriver is needed for removing the original mount and installing this one. Installation orientation is dictated by the orientation of the model in the provided STL file (positive Y is the top of the lens, the screw-hole on...

A bolt can be used on the back to hold the rod in place, depending on tolerances. Two bolts go into the neck. You will need two 3m bolts and one 4m bolt. I don't remember which size. For attaching the geared tuning pegs, I recommend using a small...

... used for small profiles to facilitate tightening. See photos. I added reinforcements to fix with 8 M5x16 screws and 8 T-nuts each time. Do not hesitate to contact me in the comments section for photos and / or additional explanations. ...

The locking pin is 3mm in diameter and 1mm thick. I want to give a huge shout out to Todd Woolums and Clay Warling for helping test out the different designs until we got them right on the money! Thanks Todd and Clay! Other designs are...

Insert it into the four holes in the corners of the middle part and cut 2mm above the surface. Then glue the middle and top parts together.</p><h5>Axles</h5><p>Two axles need to be created. The axle consists of two printed wheels and a metal axis...

70x25mm Slot shaped bases in Sector Mechanicus walkway design. ... ________________________ <b>If you like my work please consider supporting me on Patreon.</b> <a href="https://www.patreon.com/bePatron?u=30583762"...

You can see the custom made one in place now. I'm also modding those vents, they don't print very good now. Making them more horizontal than vertical. New print will be ready by tomorrow, I'll upload new models then. 06.11.2017 New top part...

Leave your questions and comments in the comment field, and I’ll do my best to answer them. Every like is appreciated! Thank you. P.S. If you like my design, Check out my other models. ...https://cults3d.com/en/users/Arlon/creations NOT FOR RESALE OR...

I have not yet tested the new design but hope to install it shortly. This is an adaptation of the Prusa MMU2S door sensing mechanism. You will need the parts that came with the MMU2S mod (IR sensor, the M2 Screw), you will not be using the magnets or...

Instead, they: -Protect gimbals from crushing within the transmitter case -Keep your transmitter case and foam in good condition by preventing sharp sticks from rubbing -Preserve gimbal springs by maintaining a neutral stick position during transport...

In other cases ABS will be enough. **You will lose 16 mm of Y.** Also there will be loss of X when using the 40x20 version. To utilize the full bed use https://www.printables.com/model/330621-ender-2-pro-y-tensioner-6-12mm-belts. **Don’t...

There's also a clip in the top to hold an optional Raspberry Pi case fan.The sleep button is a 16mm momentary pushbutton. For example: <a href="https://www.adafruit.com/product/1479">https://www.adafruit.com/product/1479</a></p><p>The remaining...