pythagorean cup 3d print

See the main image, in that filaments one and two have been unloaded by the MMU and the loops you can see are the maximum that gets pushed back on each. This solution is so much easier and quicker to load and unload than a flat panel filament buffer,...

I used the #19 drill with the depth stop (as described in the Ford Flat Head Assembly Structures for the threaded inserts) to drill holes for the magnets in the block. The Display Base was too big to print as a single part on my printer, so I split...

Notable changesGeometry added to mate with the Bear Upgrade V-Slot ExtrusionsUse either drop-in or standard T-NutsUse either M5-10 socket head or M5-8 flat head screwsTemporary M3-12 screw added to aid in sliding T-Nut alignment.Case is 3mm wider to...

Left to our own devices to scour the net for solutions, (clearly we weren't the first people with CR10S Pro V2's to have purchased this product...right?!?) well after printing three different models that just didn't fit my setup quite right, I got...

I adapted an EZABL mount to attach to the far side of the print head (opposite the fan) since I was using a 20mm thick Noctua and had no more room.I'm using this duct with the mount: https://www.thingiverse.com/thing:4042492. OFFSETS:Home...

Deprecated: Please use newer V2. This is my attempt to design a mount for the Bondtech LGX extruder with the LGX FF for flexibles hotend kit. The extruder is mounted sideways attached to a mounting plate via two M3 side screws into the extruder...

Single-color and MMU multi-color versions are included.Required materialsEach lock uses eight 8mm X 3mm (D x H) round magnets and can be attached to the enclosure with two or four 3.5mm screws.Printing instructions The lock has been designed for...

i printed mine at 0.16mm layer height in PLA. Assembly Order:Before begining, test everything out of the case. You may need to cut the casing on the drive cables in order for them to fit 1. Attach Raspberry pi to Pi Mount: I used m3 screws for this,...

FederationDN-V2-ship-stls.zip – Print-ready combined ship STL files. This kit supports the following variant ship classes: Federation class dreadnought The original TOS-era three-nacelle dreadnought from Franz Joseph’s 1975 Starfleet Technical...

Post-Printing Caravan Loft Bed DIY Instructions This model shows how to inexpensively retrofit a loft bed into a caravan. A field bed and some wood from the hardware store serve as the base. The loft bed is intended for children as a sleeping place....

Additionally, I printed 13 [quick change](https://www.thingiverse.com/thing:1996091) pen thingies for my use. Since I utilized ultra fine point sharpies, the lid didn't work as intended. Therefore, I've included the STL for my custom lid in the...

Hello.I need to “repair” my 1080Ti fans because they started to make some weird noises and low the rpms, temperatures go higer, and… why no temperature and noise reduction upgrade ?First I want say the photos are of the first functional prototype,...

I also made the spacer shaft shape wider so it is not as hard to print, nor as fragile to handle. I also eliminated a few of the sizes that I felt were not necessary. --- This is a PPC (Pixel Pipe Clip) spacer tool that will help you accurately...

For printing I just made everything 50% Gyroidial infill, with ESUN PLA+. Did a bunch of pretty serious drop and smash tests with early iterations and the unit held up pretty damn well. I got the makita mount from somewhere a while back but cant...

If you printed that set for the third edition stuff, you can now use the units as a faction (or in custom builds) for the new stuff! We've set up a Patreon page for anyone who's interested in helping to fund us so we can keep making free and open...

... points. This needs supports for building (you might try flipping it upside-down to check if you need less material - this depends on your printer. Also added full- and half-height main body extensions (these can be printed without support).

Depending on the size of the equipment to be inserted in the box, it may be necessary to print more or less intermediate parts: "Body". The assembly is done by 3 threaded rods of 4 mm in diameter and 6 acorn nuts (3 at the top and 3 at the...

So instead, I printed a separate case. Not completely satisfied with the 4 part case design, I also made a matching bottom for my case to make it easier to wire everything up. Now there are even more options. I changed out nearly every part of my...

If you repair it for printing, make a Remix, or send me another model for re-uploading. Chirostenotes (/ˌkaɪroʊstɪˈnoʊtiːz/ KY-ro-sti-NOH-teez; named from Greek "narrow-handed") is a genus of oviraptorosaurian dinosaur from the late Cretaceous...

Hobby Tool Holders This is an initial set of compact hobby tool holders the purpose of which are: Short term tool storage for tools being used on an active project Organization to help keep the bench cleaner To help facilitate rapid tool acquisition...

The kit itself includes: Front barrel extension (3 individual parts) Stock attachment piece (1 single part) Shoulder stock connector (1 singular part) Shoulder stock (3 separate pieces) Handle (1 individual part) Rifle scope (4 distinct components)...

Hello Unless you are lucky ; using a precision square will show that a printed cube is not really square in all directions. Especially if you use the portico as an handle or you let a 1kg spool gently ply it all day long... Then you have to fine...

The case is designed to be printed with a layer height of 0.2 or 0.3mm. You can lower the height if you want more details which is recommended for the ARC reactor. Supports are needed on some parts.I used PLA on everything but the electrics carrier....

I managed to get 280mm of print height out of the stock motors, and am using 16" z rods. When assembling the new frame, flip the X axis upside-down and backwards so the POM nuts are at the bottom inside of the arm instead of the top, meaning they...

This miniature comes with optional presupported files for resin printing. These files come as ready to go STL files or Lychee files if you wish to edit the supports for your custom needs. You can find my latest releases over on my Patreon!   The...

This was started on my Monoprice Select Mini, hence the size. Video Here: https://youtu.be/Ofxbj3s3f3A Print instructions You will probably have to do a little sanding or filing to get the parts to fit smoothly, but not much. I used thick CA glue to...

Only disadvantage: Ender3 only has 200x200 to 220 to 200 mm print area. The arm is too long for this Maybe a friend has a bigger printer Here is my "all-round package" with 120, 135 and 140 degree holders for the common 2kg rolls. The original...

Now fit the 80 tooth pulley printed part and secure with M5 screws and nuts. Check how long the rod needs to be by fitting the orange metal part that attaches the weights. Measure the gap between this part and the pulley. Remove the metal part and...

Then, for now, the program just prints out that z height planes as a layer text to the output file to show that we have at least gotten this far with the program. USAGE: slicer.pl input_file.stl output_file.txt I included an STL model because it...

Print two each of profile holder and spool holder, plus 8 spacers. You will also need 4x 608 bearings and minimum 4x hex nuts and bolts (3x20 will do, but they can also be longer if that's what you have). To secure the holder to the profile...