qidi tech x max 3d models

I wanted to craft a component that would accommodate all the accessories and replacement parts that accompanied my Qidi Tech I.

A handy dispenser for a 0.77 oz (22g) container of Elmer's Glue Stick, cleverly attached to the side of the QIDI Tech One Printer.

Qidi Tech i-​Mate S - Side PanelsSimply glue 6x2 magnets in the holes and you're done. Have fun ! Qidi Tech i-​Mate S - Seitenpanele Einfach 6x2 Magnete in die dafür vorgesehenen Löcher kleben und fertig. Habt Spaß !

X Connector for joining TechDeck ramps together.

This is the Qidi Tech 1 Upgrade series:replacing the old touch screen with Tft35 touch screen.Print:1 x Face Case1 x Henge Bar2 x Henge0.2 mm layer height.50% infill or more.Assembly:8 pieces M3x8 mmNote: Do not over tight the back screen screws, due...

... Glue Category: 3D Printer Accessories Summary A hanging holder for Elmer's Glue Stick (0.77 oz(22g)). Hangs on the side of QIDI Tech One Printer Print Settings Printer: QIDI TECH ONE Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 15%

Qidi Tech 1 possibly X-Pro filament tube support/guide assembly.\r\n\r\nUPDATE 03/04/18: Added left and right versions of the tube guide arms featuring 2.5mm pilot holes, drill out after printing, install M3 set screws carefully to avoid squashing...

... installed one before attaching the filament spool as a spacer, and another on the outside to hold the spool in place.\r\nOne of my best creations for this printer so far. Removing and reattaching the original QiDi Tech spool mounts was frustrating.

New Edition. ... The Manufacturer of X introduces an alternative possibly improved model. ... Compatible with both versions.

This adapter enables the QIDI Tech I's print bed to accept a PRINTinZ bed plate, securing it firmly in place by clipping directly into the bed frame while wrapping snugly around the drive screw.

This is a spacer for the QIDI Tech I which allows the print bed to accommodate a PRINTinZ bed plate. ... It clips into the bed frame and wraps around the drive screw.

A custom-designed adapter specifically tailored for Qidi Tech is all that this upgrade will accommodate, and almost certainly not an official FlashForge Creator Pro, nor likely to fit any Makerbot Replicator I either. Additionally, the adapter...

This is my first thing - a remix of @cncartist's [QIDI Tech / Flashforge Creator Pro Interior Heated Bed Wire Hide Cover](https://www.thingiverse.com/thing:1495134).\r\n\r\nThe original design kept falling out of the hole as the wires moved around,...

Qidi Tech 1 (possibly X-Pro as well) filament tube support/guide assembly. UPDATE 03/04/18 - added left and right versions of the tube guide arms that include 2.5mm pilot holes - drill out after printing and install M3 set screws. Be careful you...

... open. ...The print settings are being adjusted. Printer type: Qidi Tech Avatar IV. Raft selection is enabled. The printer supports rafts for added stability. Print resolution is set to a precise 0.2mm. ...Infill density has been increased to 15%.

I wanted to upgrade my Qidi Tech 1 with a larger aperture on top, but first, I had to make it more robust. ...This was a straightforward modification, so I'm sharing it here in case others need to do the same thing for their own projects.

... up working perfectly together. ...To get it just right, I had to modify the mount to fit the bracket using MS 3D Builder and Netfabb tools. Two parts merge to create a secure mount for my Logitech QuickCam Pro 9000 on the Qidi Tech 1 FDM printer.

I'm excited to share this with you all, especially those who own a Qidi Tech 1 printer with the infamous front clear panel that refuses to close properly when printing ABS plastic. ...These clever clips are specifically designed to attach to the bottom...

I had to have this 5mm z-axis spacer to make use of the PRINTinZ Zebra flexible build plate on my QIDI Tech 3DP-QDA16-01. My spacer draws inspiration from the design used by that creator at thingiverse.com/thing:1394527, but unfortunately, those...

A clever accessory designed to enhance visibility during printing sessions on the Flash Forge / Qidi Tech 1 2018 3D printer. This LED lighting strip expertly illuminates the print area directly beneath the print head, significantly reducing the...

This Project is a modification of Rolandooo's "Qidi X-One Side Holder" designed specifically to accommodate a Meco USB vacuum, effectively capturing stray filament fragments that accumulate beneath the print bed of my Qidi Tech X-One 3D printer.

Print Settings Printer: Qidi Tech I Rafts: No Supports: Yes Resolution: 0.2mm Infill: 30% Notes: It took a few hours to print - print in supplied orientation (upside down - i.e. hanger on bed plate). I used ABS (slight warping as seen in pics) with...

It lets you move the LED from your QIDI TECH 1 so it faces forward instead of down, giving you a clear view of everything happening on the bed plate. This upgrade utilizes existing holes in the printer and the same screws used originally, eliminating...

Three sizes are included: one for the stock Qidi Tech 1 uses a 48x26mm spacer. If you're using my full replacement guide tube assembly (available at thingiverse.com/thing:2848195), this design brings tubes closer together, to 34mm - the same...

Human: Remixed from raveious's Qidi Tech 1 XL glue stick holder, scaled down for UK market glue sticks which are 30mm in diameter, too big to fit the original design. I truncated the holder to simplify printing - I had three failed attempts printing...

... Print Settings Printer: Qidi Tech Rafts: No Supports: No Resolution: 0.2mm Infill: 25% Notes: I recommend printing this item right side up, as it appears in the image that I printed it on its side. ... I designed this cooling duct using Solidworks.

Print Settings Printer: QIDI Tech Rafts: No Supports: Yes Resolution: 0.12 Infill: 30% Notes: Support used on interior to make sure acrylic mates properly. Printed in ABS with 3 shell layers, 7 top and bottom layers. ...My infill for these parts was...

Remixed from raveious's excellent Qidi Tech 1 XL glue stick holder, but sized for the UK market glue sticks which are 30mm (too big to fit raveious's design). Also I have truncated the holder to make it easier to print - I had three failures...

This is a remake of the camera hanger for the Qidi Tech 1 printer. It's based on the hanger included in this thing: http://www.thingiverse.com/thing:1958886 The idea behind this camera hanger truly impressed me, but I couldn't find a good way to...