quadcopter f450 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

After studying what was available, I started modeling my own. The problem was that most of the projects were on console tables, but our table is held on two rails, one on each side. Initially, the project was implemented on a seven-string polispast,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

The COMPLETE Dumlok Flameseekers bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! This set includes: 12 Dumlok Flameseeker (modular figures + figures with helmet)The Dumlok,...

Which means planning so the bridges will look nice enough/not stand out too much.This also means some very precise modeling so that the slicer can handle a bridged over area with a hole in the middle. Here, I build up to it layer by layer with...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 0 custom_corner_resolution = 8 stencil_drawing =...

... I repaired the model and added a cover plate that screws over the motor plate to quiet it down. - Updated 6/2/2021 I reuploaded everything, Something got messed up and a few files where missing. This includes a camera mount arm I made as well.

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.8. Can...

Trim/Cut plastic flowers from a dollar store. Modified from this model: https://www.thingiverse.com/thing:3666273 Photo frame with a sliding/rotating cover. Slightly recessed oval of 40mm wide by 55mm tall to attach a 2D printed image/photo. Three to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

I usually split such models on 2 or 3 parts that are easier for printing. Then these parts can be glued as a one piece (with acetone for ABS, or dichloroethane for PLA). So other version of parts I am uploading is prepared in this way. My black...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.3...

The assembly requires some M4 bolts and nuts, RGB strips, a hot glue gun, and tubing with a external diameter below 13mm (I have used 11mm). If you have any feedback, issues, or suggestions for future improvements please comment in the comment...

[Medium Sized Model - 25mm Base] [Presupported in 32mm & 75mm scale]   The third child of Tharador, Renmaeth is the custodian of his body, the continent of Tharador. In the Age of Creation she shaped the mountains, tended the forests, sanded the...

** FUSION360 and STEP Sources are included **** I have my printer into an enclosure and, to save the electronics from excessive heat, I've designed this model to enclose all the electronics at a singe location. These were my requirements: -...

The COMPLETE Requiem Brotherhood bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! This set includes: Requiem Templars (presupported) Requiem Templars stand before the chaos and...

Really like the wheel from TheSloppyApprentice's Watermill and was looking for ways to hold it besides that large frame in the source.So I could make it stand in a bassin or hang under some opening where water is dropping off.So here are 2...

Model of the pusher cap and the skirt part used on an On/Off switch combination cast aluminum IP40 case The case with two momentary switches made more than 40 years ago in the GDR (do not call it East Germany, please) works still perfectly fine. It...

I have printed the model in 2 colors with an extruder, changing the color of the filament in Z: 150, except in parts 1,2 and 3 that have part of the roof and I have changed it in Z: 150.02. The dial I have changed the color of the numbers. I bought...

If you look at the print of the base (or the model of the legs) you will see there is a round hole with three slots surrounding it. These slots fit a specialized washer that is used in the vise to keep the base from rotating when it has been...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_x_size = 30 custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30...

I changed the position of the threaded inserts and added additional to replace the hex nuts. Modified the cable paths and tie wrap holes for easier printing, and thickened up some sections to print better. Modified how the front and rear clamp...

Included are the STEP and STL files for all the printed parts along with a Fusion 360 model link: https://a360.co/2QkvXpV **I feel it important to acknowledge Roberto Gil (jgbbob8) for his contribution to this project. When in late 2017, I added the...

This project is intended for use with circular lenses that are delivered in glasses ordered from Zenni Optical with this particular frame: https://www.zennioptical.com/p/metal-alloy-full-rim-frame-with-spring-hinges/5500 For either model of Quest,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 4 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.4 stencil_pattern_line_thickness = 30...

Note: these videos are uploading slowly, so they might not be fully processed when I publish this model. They should be available in a few minutes.</p><figure class="media"><oembed...

Just drag the lithophane (standing up) to the mount, and position it so that it intersects the model, while lining up the curved edges as seen in the picture. 3. While that is printing, disassemble the nightlight by pulling off the diffuser,...

You can find a similar model at Amazon, the "MakerHawk USB Multimeter USB Voltmeter Ammeter Load Tester USB Voltage Current PD Battery Power Capacity Charger Digital Type C Meter Tester Color LCD Display Cable Resistance QC2.0/3.0/4.0 MTK " (lol) -...

This print allows to elegantly mount your Bosch eBike Charger to the wall, out of the way, right where you need it. I made this version because several people indicated that they liked my eBike Charging Station but preferred a standalone version of...