quanum cyclops fpv goggle 3d models
19861 3d models found related to quanum cyclops fpv goggle.thingiverse
This is a hatch cover for the Quanum Cyclops FPV goggles with a hole and holder for a 0.96" OLED display as used woth the Cyclop+ firmware mod https://github.com/Dvogonen/cyclop_plus To get the old hatch off I opened the goggles and used a craft...
thingiverse
Items: Goggles: Quanum DIY FPV Goggle Set with Monitor (KIT) Video Receiver: 5.8G Wireless FPV RX RC305 Battery: Gens Ace 1000mah 3S 11.1v 25C Switch: RL3-5 series round rocker switch Male & Female XT60 connector All feedback is appreciated. ...Print...
thingiverse
If you have a bulky old Quanum Cyclops V1 laying around, just turn it into a sleek FPV monitor for spectators. You need: - Quanum Cyclops V1 - XT60 Connector (optional) - 4x M3x12 of M3x15 screws - double sided tape (1mm) ToDo: - Open your Quanum...
thingiverse
Quanum DIY FPV Goggle V2, are very nice low cost PFV goggles, bu they have a big defct: it is impossible to focus, because the focal plane is about 9cm beyond the screen position .... This adapter allows you to put the image in perfect focus. ...
thingiverse
... ... I decided to use it as the 2nd camera on my Quanum V2 goggles. This is what I came up with, a design which mounts to the back bracket features of the V2 monitor using zip-tie. And an open design to allow airflow to keep the board from overheating.
thingiverse
This is a redesigned lens holder frame for the Quanum FPV Goggles V2 from Hobbyking. I designed this frame for using Fresnel lenses from Optolife.com with the Quanum goggles. Order the lenses from here and cut to size with for example circular...
thingiverse
Cover that integrates the FPV 5.8 GHz 32CH RC832 receiver board into the body of the Quanum DIY FPV Goggle Set with Monitor (KIT). Instructions This mod requires the RC832 be removed from the...
thingiverse
“S” loop for quanum V2 fpv goggle top strap adjustment to improve wearer comfort and fitting Layer: 0.15 Fill: 100
thingiverse
Case to attach a cheap CCD camera to your Quanum DIY FPV Goggle V2. Printed in PLA, if you flip over the top case obviously prints easier. Support needed on the back to allow for hooks. ...Needed a slight file around the hooks to ensure a nice tight fit...
thingiverse
this is a replacement for the fresnel lens holder included in the HobbyKing product "Quanum DIY FPV Goggle Set with Monitor" http://www.hobbyking.com/hobbyking/store/uh_viewitem.asp?idproduct=53706 I would appreciate if you could leave a feedback...
thingiverse
This is a replacement for the lens holder of the Quantum DIY FPV Goggle V2 Pro. ... You will need 4 m2,5 screws to hold it together.
thingiverse
These are an cap for my FPV goggle. inside is a holder for the boscam reciver. I have make a hole and some heat slots (?) for it, becouse it will be hot after a hour or 2 :) will edit a picture when i have it build in Make your Boscam reciver inside...
pinshape
This is a way to use the Gopro head strap with the quanum V1 headset (much more secure then what comes with the Quanum kit). I made this to be usable without having the modify the head strap, just unhook the back plate. Cut a hole to fit the mount...
thingiverse
Wall Mount for Hobbyking Quanum FPV goggles. ...Print with the long side on the bed.
thingiverse
Integrates the RC305 5.8Ghz Receiver into the Quanum DIY FPV Goggles.
thingiverse
This is my first attempt at a holder for the Immersion RC Uno5800 to mount to the Quanum FPV Goggles. Print is 3 pieces: 1 x Uno 5800 Holder 1 x Base To Back Connector 1 x Back plate Other parts required: 1 x m3 20mm screw 1 x m3 nut Cable...
thingiverse
The idea of these models is that they fit onto the Quanum V2 goggles (without needing glue) and create wider platforms to mount sponge pads on, to distribute the pressure on the wearers face. I haven't got the right foam at the time of printing, but...
thingiverse
Designed to hook a strap through a slit made in the quanum goggles foam. ... There is an indent to suggest where to cut, Simple make a slot, stuff some strap through, and use this on the inside to hold it in place.
thingiverse
Remake of Quanum DIY FPV Goggles Vrx RC832 Cover by Johnny01. ...Thicker walls to make it stronger.
thingiverse
Parts to improve Quanum FPV v1. Spacer increases the focal length, and is sized to mount Galaxy S4 or S5. Screw on with small self tappers. Mount screen with a rubber band. Buckle makes attachment of strap easier to foam goggles. Lensegrab is a...
thingiverse
It is a remix of the fan shroud for fatshark for my Quanum Cyclops v2 A little bit larger and holes for M3.
thingiverse
I wanted to clean up my dangling fpv receiver setup for my quanum goggles. So I made an interface box to easily be able to exchange parts to a fpv ground station. I borrowed the ball joints from Giufini to fix a patch antenna and be able to aim it. ...
pinshape
This is a simple and protective pod built for the Quanum DIY FPV kit V1 from hobbyking, With some velcro on the back of the camera it fits very snugly. the VTX is QR zip-tied upright only because I have no 90 bent antenna. ... Printed with ABS,...
thingiverse
This is how the Quanum should be. Remove the RC832 case and wire it to the monitor. ...Then, add this cover and you are all done.
thingiverse
Solves problem for people with glasses (putting goggles on and taking them of with eyeglasses is sometimes very uncomfortable) Print Settings Printer: K8200 Rafts: Doesn't Matter Supports: Yes Resolution: 0.25 Infill: 50
thingiverse
Just added a few extra bits to help the goggles sit more comfortably on my head.
thingiverse
If you have a Quanum Cyclops FPV Goggle and you need to wear glasses you might feel uncomfortable. Since this Goggle is shipped with an additional spare fresnel lens I tried to put these 2 lenses in serial. And it works: I don't need my glasses in...
thingiverse
Modified to not require supports on the inside of the model. ...Not the best modification but it works.