quick shoe laces 3d models
85976 3d models found related to quick shoe laces.thingiverse
This is a quick shoe lace based on the Klots design. This model is in 3 parts. The border , the body and the stars. I recommend printing all the parts with 100% infill and to print the border with a flexible filament. ( quite hard still ). The parts...
thingiverse
This is a remix of the 1st Quick Shoe Lace, with a different design. Just print with your preferred colors and CA glue the parts. ... The parts are all designed with a tolerance of 0.2 mm to ensure an easy assembly.
thingiverse
This quick lock shoes laces buckle is very easy to print and to use,this one is printed with Tristarbot M1 3d printer,ABS,Nozzle 240 degree celsius ,hotbed 105 degree celsius ,you can order the Tristarbot M1 now on amazon...
thingiverse
this is a quick lock shoes laces buckle,from now you never need to deal with your shoes laces anymore
thingiverse
Now you can run or go about your day with a quick release mechanism for your laced shoes. set the magnets in with glue, so they won't come out. and be sure the magnets are flipped to correct polarity before you set them in otherwise they will...
prusaprinters
Now you can run or go about your day with a quick release mechanism for your laced shoes. set the magnets in with glue, so they won't come out. and be sure the magnets are flipped to correct polarity before you set them in otherwise they will repel...
pinshape
This is a quick lock laces buckle,from now you never need to deal with your laces everyday.
myminifactory
This buckle was printed of ABS, 100micro layer, with the 3d printer tristarbot M1 which you can order on amazon now https://www.amazon.com/dp/B06XFLZN8N?m=A2X9LSXLK64D5N&ref_=v_sp_widget_detail_page
thingiverse
Tried to make some Quick Laces that kind of slide together. These are a little more minimalistic than other found here. Test them out make suggestions and I'll improve them because right now they are still being tested. ...Thanks!
thingiverse
The ends of the top lace are shorter on 0.5mm, the bottom lace is narrower of 0.4mm. It's not a big deal, you can print just the top lace twice, I think. Warning: despite of the laces matches perfectly on the model, be prepare to tune them in place...
thingiverse
While there are already many designs on Thingiverse most of them are quite massive in size and won't fit shoes with only little space for the laces. This is why I designed these magnetic laces which will fit better in that situation. The width of...
prusaprinters
The parts are sticking together by using a small hook and a magnet.While there are already many designs on Thingiverse most of them are quite massive in size and won't fit shoes with only little space for the laces. This is why I designed these...
thingiverse
v2 is an all around improvement, see it here: https://www.thingiverse.com/thing:4825022 Back in 2019 I broke a boot lace with only an hour before I had to leave for a meeting, so I figured I'd print something up to replace it. Printed in TPU at...
prusaprinters
Then, starting at the bottom of the shoe, push the tip of one of the ends through the eye-hole, and then use a tweezer from the inside to pull the rest of the tip through. Repeat for the corresponding eye-hole on the opposite side. Work your way up...
thingiverse
I have uploaded STL files with the following lengths: * 40mm * 45mm * 50mm * 55mm * 60mm * 65mm * 70mm To figure out what size you need, put on a shoe and measure the distance from one eye-hole to the opposite eye-hole. If you notice that not all...
thingiverse
Just in case your shoe doesn't get tight when placing this at the end of the laces, there is a hole to place a pin through the part and anywhere on the shoe to make it as tight as needed. If you make this part please upload a picture. Print...
thingiverse
Based on the dust shoe design by @comuter (Ref: https://www.thingiverse.com/thing:845554/files) i designed a quick change attachment to easily accommodate different end mill lengths. I am using a 2mm transparent foil (industrial curtain) and not...
thingiverse
standard print settings tie to your shoes, and your set to fly. ... print two wings for each shoe, or just one for each shoe and print the matching wingless pieces.
myminifactory
standard print settings tie to your shoes, and your set to fly. ... print two wings for each shoe, or just one for each shoe and print the matching wingless pieces.
thingiverse
There are 3 different models available: Klöts 3 - For small shoes and kids shoes Klöts 4 - For average sized shoes Klöts 5 - For big shoes and boots 27.7.2015 Added strips to make Klöts look even cooler and more personal. How to use? 1. Undo...
cults3d
There are 3 different models available: Klöts 3 - For small shoes and kids shoes Klöts 4 - For average sized shoes Klöts 5 - For big shoes and boots 27.7.2015 Added strips to make Klöts look even cooler and more personal. How to use? 1. Print...
cgtrader
single shoe (sneakers booty gumshoe) made in Blender and saved in Blend.file
thingiverse
Magnet Version of Klöts (Quick shoe ties) Magnets: 5x3mm -> http://ali.pub/38zsjr
myminifactory
This is a Go Pro quick release shoe mount. So the baseplate is placed on the shoe. ... For wakeskating, longboarding, but also mountainbike, etc.
thingiverse
A quick release plate with hot shoe mount. ... Instructions May need to drill a hole for locking.