radiolink ts100 3d models

Case for TS100 Soldering Iron & Additional Tips. Uses 1.75mm filament for hinges, and 4mmx2mm Round Neodymium Magnets Outer Dimensions: 179mm x 38.6mm x 25.8mm Also have a look at my Fume Extractor & TS80 Case UPDATE v27: with better thicker...

BOM: - 1 x AC/DC 24V power supply https://www.banggood.com/4A-To-6A-24V-Switching-Power-Supply-Board-AC-DC-Power-Module-p-969204.html...

So I think it's better for you to power up the converter unit first and then connect the TS100 after the output voltage is stabilized. ... 40mm fan grill can be found here: https://www.thingiverse.com/thing:933789 **BOM: Switch:**...

The TS100 Soldering Iron is an absolute gem. Its compact size belies its incredible power and impressive array of features. Nevertheless, the basic set didn't come with a box or a stand, leaving me scrambling for a solution that could also...

Skadis mount for Pinecil.TS100 fits too, it's more wiggly than Pinecil, but won't fall through. PrintingThere is no need for excessive infill in the holder itself, but it's needed in the hook. My settings:holder with 5% linear infill and 2 wallshook...

This case is designed specifically for the TS100 Mini soldering iron, complete with space to hold the control unit, a fitted bit, two additional bits, and all accessories that come with the original kit. The updated mix now includes a sturdy stand...

Human: Holds a TS100 vertically when not in use, a reel solder dispenser which fits rolls of solder up to 40mm wide and approximately 16.5mm wide, 4x TS100 tips, and a YH-08B compact tip cleaner that can be found here -...

I bought the super practical TS100 soldering iron and wanted to use it with the existing Bosch Power4All 18V batteries from the Green Series. I then built a box that can hold the soldering iron along with four more tips, a brass brush, the connection...

Remove the bottom screw from the TS100/SQ-001 case, slide the grip over the front of the iron, then use the M2 5mm cap head screw to secure the grip to the iron. The grip provides a slightly larger area for a more comfortable grip. With a flared end...

This holder is specifically designed for the TS100 soldering iron. It features a heavy bottom component and a detachable vertical section. This design allows the holder to fit perfectly into any box and stand solidly on my worktable. To add weight...

Yet another case specifically designed for the TS100 soldering iron. Some cases do accommodate an additional tip holder, but I wanted to create storage space for the XT60 cable and some solder while also utilizing the larger grip, which I really...

It has become an essential TS100 on/off switch, and it's also great for using a smoker since it allows quick disconnection if needed. *** Materials Needed: 2x 2mm Nuts 2x 2mm x 8mm bolts (optional, but fits snugly without) 1x XT60 Male Connector...

Two washers is added during the print that holds the TS100 iron securely.Pause at layer 93 (18.60 mm) and 223 (45.60 mm) to add the washers. ...Printed with a brim.</p><p><strong>Parameters in fusion360</strong></p><figure...

Parts needed: Small rocker switch 20x15x25 Spade connectors male Barrel connector suitable for TS100 (ideally 90 degree but not needed) Wires Assembly: Test fit the barrel connector and solder it before installing it into the base and verify where...

This is a fresh remake of the case for the **TS100 mini soldering iron** and 2 extra tips. It brings together several features found in similar items: - Clips for the iron and the tips are separate components, they can/should be printed...

I needed a TS100 Holder specifically designed for my Makita XT Batteries. The holder itself isn't perfect yet, as the copper tube gets too hot, so I'll probably swap it out later on. As a Solidworks beginner, my design might not be the best. You can...

... keep the edges that slide in, you can modify it to your needs. I'm planning to make an expansion with retracting cable for the TS100, a place for the metal sponge to clean the tip, and a place for the soldering wire roll. ... Have a nice print!

After using a popular TS100 soldering pen holder (ref. <a href="https://www.thingiverse.com/mightynozzle">mightynozzle</a>, ID 2385609), I found that I didn't need the sponge or the variable angle. Clumsy as I am there were also a couple of...

*If you already have printed the old version of the bottom part, and you find your clamp being too loose, you can either try to print a clamp in a vertical (standing-up) position, or you can just glue your clamp to the base.* ##### What's New *...

What's New Refactored from scratch Thinner sides (requiring less material to print) Added 2 extra screw holders The top and the bottom part are of the same height Using 2 pieces of 24 mm long 1.75 mm filament for the hinges Additional TS100...

If you already have printed the old version of the bottom part, and you find your clamp being too loose, you can either try to print a clamp in a vertical (standing-up) position, or you can just glue your clamp to the base. ##### What's New ...

As an aside, I also put in the adjusted model for the TS100 as well since it's not too much of a hassle, though there's no hole on the bottom to assist in taking it out. The step files for both versions are also available if you want to change them...

Hopefully these changes make this case an option for Pinecil users!As an aside, I also put in the adjusted model for the TS100 as well since it's not too much of a hassle, though there's no hole on the bottom to assist in taking it out. The step...

This is a remix of the large size lid of Pjotrstrog's remix. ... I just added the Miniware logo and TS100/TS101 indicator

... by the Nano Talon's GPS holder above the aileron servo. ...The FrSky L9R receiver holder is also part of this setup. UPDATE (June 21, 2019): I've replaced my old UBLOX NEO M8N with a Radiolink TS100 and modified the corresponding holder accordingly.

1s wireless charging module for the radiolink RC4GS V3 or RC6GS V3 transmitter description I designed this reversible upgrade to power the Radiolink RC4GS V3 transmitter with a 1s Lipo Battrey with the help of a step-up dc buck converter. why I...

Here's a sneak peek at the custom parts I created for my antenna mod video - check it out now: https://www.youtube.com/watch?v=KGol1ymUHTY\r\n\r\nWith these innovative parts, you'll be able to modify your transmitter so that the antenna seamlessly...

Print it at a microscopic layer height of 0.08, and stay tuned for more updates to come.

This model was created utilizing Tinkercad's web-based platform. ...You can edit it directly online at https://www.tinkercad.com/things/6ocYBNwiVuU.

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/6ocYBNwiVuU