rakonheli inductrix frame 3d models
105073 3d models found related to rakonheli inductrix frame.thingiverse
This frame weighs in at 9.30g which is lighter than the original RakonHeli frame and proving to be much stronger. Parts List: All nylon screws for hardware Super S F4 FC with OSD Fishpepper 5A BB2 48MHz DSHOT600 1-2S 4in1 ESC Flex-RC 1102 15000kv...
prusaprinters
The finished product weighs in at 35.6g with ll02 motors. This frame weighs in at 9.30g which is lighter than the original RakonHeli frame and proving to be much stronger. Parts List: All nylon screws for hardware Super S F4 FC with OSD Fishpepper 5A...
thingiverse
inductrix frame 2 gramm more than the orginal but stronger the motor holes must drilled, first 5,5mm than 6,0mm Print Settings Printer: colido
thingiverse
Frame weighs 5 grams All up weight is 21 grams, same as stock inductrix. Print Settings Printer Brand: Robo 3D Printer: ...
pinshape
Alternative frame for the Blade Inductrix indoor quadcopter. I made this design after having trouble finding a design that I could reliably print on my printer(s). My friends and I do little indoor obstacle races, and it is difficult to tell the...
thingiverse
Alternative frame for the Blade Inductrix indoor quadcopter. I made this design after having trouble finding a design that I could reliably print on my printer(s). My friends and I do little indoor obstacle races, and it is difficult to tell the...
thingiverse
Yet another Inductrix Frame Support. I have used this on a busted frame with good results. ... Hopefully this will be of use to someone.
thingiverse
*New version of the frame added "Inductrix frame rev2 no scallops" has straight ducts, as well the fc board mounting holes have been adjusted so you dont need battery tray component. Print Settings Printer: Creator pro ...
thingiverse
Blade Inductrix Frame. Use a drill etc to bore the motor mounts if it doesnt print perfect on your machine, other than that the other prep is easy, after print takes about 20 minutes to prepare and assemble. Flies well, a little more sluggish than...
thingiverse
This is my take on the Inductrix frame support. The curves provide rigidity for side by side motors. With PLA, this should weigh approximately 1.6g. ...There are 2 version: FrameSupportV03_64: ~64mm diagonal wingspan FrameSupportV03_65: ~65mm diagonal...
thingiverse
inductrix frame replacement that uses fpv micro camara Frame + camara mount Average 4.5 grams Print Settings Notes: nozzle size .4 printed in ABS but you can use anything model is printed facin down on the flat part , frame and fan shroud must be...
thingiverse
This is an 104mm picnic frame for the Blade Inductrix FC, 7mm Hubsan motors and props and the FX797T cam/vtx combo. I changed the power cord to JST to be able to use 400mAh 1S lipos and used a short velcrostrap to fix them to the frame. I also used...
prusaprinters
inductrix light weight frame made for simplify3d 1 to 2 walls motor cap have made out of flex Print Settings Printer: flashforge PRO Rafts: No Supports: Yes Resolution: .18 ABS Infill: 15% none used Category: R/C Vehicles
thingiverse
This is a frame stiffener for the Inductrix FPV. It will save you a few broken frames from hard landings. It should be a nice hand press fit and has clearance built in for the motor wires. The web is 1mm wide and 5mm thick. It gives great rigidity...
thingiverse
This frame is for the inductrix blade micro quad. No extra hardware is needed, you can mount the battery either above the FC like in the picture or below (mouting holes are included). I didn't use the rubber spacers included on the original frame,...
thingiverse
6mm motors should fit nice and snug when printed in ABS (not tested it with pla) You may need longer screws to mount the board (I'll do an update with raised mounts like the stock frame) EdIt: Added mk2 file with raised fc mounts to fit the grommets...
thingiverse
Horizontal 2S 300-550mAh Battery Holder for Rakonheli Brushless Whoop Frame (both 66mm and 76mm versions)
thingiverse
Vertical 2S 300-550mAh Battery Holder for Rakonheli Brushless Whoop Frame (both 66mm and 76mm versions)
thingiverse
3S 300mAh Battery Holder for Rakonheli Brushless Whoop Frame (both 66mm and 76mm versions)
thingiverse
Its a Plane shaped inductrix tiny whoop frame. There is only one motor guard in the motor guard file. ...You will need to print 4 of motor guards..
thingiverse
nice light frame 3,4 gramm for Blade inductrix. ...Here a video nice littel bastard FROG https://www.youtube.com/watch?v=yrruJX4b7Tw
grabcad
Here is my modified Blade Inductrix / Tiny Whoop Frame.I have heavily modified it to achieve a stronger more stable frame. The weight is within 0.1g of the original. CAD will follow depending on how well it works. ...It's currently 3D printing on an...
thingiverse
Tired of those broken frames on your Blade Inductrix? With this Mod it won't happen again as the forces are distributed to all Motors! This is Version 2. print it with solid fill and it will be just as good as the first version at half the weight!
thingiverse
Stock Inductrix frame weight - 3.5g I have noticed when using higher then stock KV motors (17.5K and above) the rigid nature of this frame can cause some slight flight controller high gain behavior. Nothing that is significant enough to effect flight...
thingiverse
RKH Inductrix Frame Battery Holder 3D Printable Replacement. Print Settings Printer Brand: Printrbot Printer: ...
thingiverse
A very basic and lightweight frame for the inductrix FPV Pro. 6 mm motor mounts. I have omitted the battery mount and opted for a simple elastic band to secure the battery. This saves weight, and places the battery as close to the COG as...
thingiverse
This is a Nano QX frame I designed in FreeCAD. I'm not sure how it even performs, weighs, etc. ...because I don't have a 3D printer, but here it is.
thingiverse
my scale is not very accurate but seems this thing became little bit lighter than original frame, lot lighter without ducts. frame can be build with or without ducts and duct can be removed, replaced or installed later. material abs + 1mm carbon...
thingiverse
Battery holders for the Rakon Inductrix frame. ...Works perfect when printed out of TPU
cults3d
Easy to print Inductrix quad frame. Heavier than original frame, but pretty robust as well. ... Normal frame file for 0.5 nozzle, thin file is for 0.4 nozzle.