rammstein 3d models

However another person created this and the subsequent prusaslicer ini file. however I am not quite knowledgeable enough with gcode and prusaslicer to make the necessary adjustments to it to make it work on the mini (plus I prefer to do it directly...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_y_position = 0 stencil_drawing =...

They are both definitely WIP, I do not own a Orbiter V2 and are based on the CAD models. Update:18\10\21 Uploaded some 5010 fan ducts which are 8.5mm longer to allow for a Volcano Hot End. These are definitely WIP. I have not printed, installed or...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

2022-04-14 I started to create a new base that could use threaded inserts and quickly realised the base models had become quite complicated due to the iterative design process, so I went back to basics and recreated them. The new housing mechanism...

I hope this piece works for you; it was actually the most challenging to model and get right. 9. You should be good to reassemble now! 10. Put the hammer-trigger-piston assembly back in. 11. Lay the cylinder back in place, including the U-clip for...

This helps with the strength of the threads as it will be printed length wise on the build placeThis gives more freedom to place pieces in any orientation, as well as add spacers between larger parts for more accents and individualityFixed stringing...

While it worked okay for most things, there came a time when I was trying to print a model with steeply overhanging points and the stock cooling just wouldn't cut it. I designed this adapter to allow a standard 5015 radial fan (24 volt, 0.1 amp) to...

Rollerspooler is the latest in TUSH-Varientalology, using the base Idea from the original The Ultimate Spool Holder (by filamentry) then adding the Clamp from the original Prusa Spool Holder (because, why reinvent a perfectly working wheel?) to mount...

The pilings for this model are 20mm - slightly shorter than for Huts 1 to 4. If you want an easier time of it, you could just print shorter independent pilings, so the huts are not raised so high and its just a single step up into them from ground...

The pilings for this model are 20mm - slightly shorter than for Huts 1 to 4. If you want an easier time of it, you could just print shorter independent pilings, so the huts are not raised so high and its just a single step up into them from ground...

The pilings for this model are 20mm - slightly shorter than for Huts 1 to 4. If you want an easier time of it, you could just print shorter independent pilings, so the huts are not raised so high and its just a single step up into them from ground...

Some photos of the printed mod installed on the machine may differ from the STL due to the fact that my machine is a prototype, and I decided to change some details after discovering potential issues (so I updated the models, but for lack of time, I...

For that reason, the drawers shown here have been modeled by means of [OpenJSCAD](https://openjscad.xyz/dokuwiki/doku.php), which give you the possibility to adjust them just by changing a few numbers and [rerun the script in your...

The pilings for this model are 20mm - slightly shorter than for Huts 1 to 4. If you want an easier time of it, you could just print shorter independent pilings, so the huts are not raised so high and its just a single step up into them from ground...

Larger or smaller screws can be used if you scale the model accordingly e.g. M3x8 screws at 150% part scale. Note: it's cheaper per screw if you buy in bulk from a specialist supplier. There are two versions of the container available, the standard...

The pilings for this model are 20mm - slightly shorter than for Huts 1 to 4. If you want an easier time of it, you could just print shorter independent pilings, so the huts are not raised so high and its just a single step up into them from ground...

My printer is a I3 Pro Dual Extruder, so I know for sure it fits that model and probably all of the I3s that were made with that frame. Update 1/22/18: I added a new mounting plate that moves the stepper motor forward. This allows the X carriage to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_corner_radius = 5 custom_left_port_corner_radius = 5 custom_phone_width = 100 custom_bottom_port_corner_radius = 5...

Found a simple hip flask just laying about USHip flask discovered seemingly abandoned USHip flask uncovered, left behind USHip flask in basic design chanced upon USHip flask, a basic model, was stumbled upon USHip flask, plainly designed, was located...

- The barrel at the front stabilizes the cars but is limited in size, preventing some models from fitting inside. However, a vast majority should fit without issue. PRINTING: - I print the main body and shaft separately from each other, as well as...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_corner_radius = 5 custom_top_port_corner_resolution = 8...

* Test your work again * replace the toothpick with the mounting pins * improve the models and share your changes with the rest of us! The difference between this and the original is that I have add a version of the body which has an opening...

Another thing to note is that there have been a few minor changes to the model since I printed the one in the pic, however I don't think anything changed will cause a problem. The STP file is included for remixing. Just wanted to mention some info...

Cheers. Print Settings Printer: D-Bot Rafts: No Supports: No Infill: 20% Rectlinear Filament: DASFILAMENT PETG Trans Blue / Trans Green Notes: You need: a heatbed because of the big surface of the model A coolerfan for the threads Category:...

So I grabbed [YucA305](https://www.thingiverse.com/yuca305/designs)'s [Drag_Chain_YZ_Slipon.stl](https://www.thingiverse.com/thing:4648673), put it into SketchUp Online, used the STL as a mask for sizes and alignment, simplified the model a bit and...

The models (keys and legends) are the same dimensions and should center at the exact same spot. It’s really difficult, and you will fail again and again, but the result is worth it (I think). You could also print the keys upright (with supports) and...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

... The models are in the position, they should be printed. No support is needed. I suggest to use a 10mm brim for the tube to prevent it from detaching from the buildplate while printing this tall piece. Printed on an Ender 3 Have fun!