ramps 1.4 test code 3d models

This mount is beefed up from the original RAMPS 1.4 mount to fix some of the original breaking issues I had. Simple mount that holds a RAMPS 1.4, Re-Arm Smoothieboard, and cooling fans. Slots in side of "case" allow for neat running of stepper motor...

I haven't tried printing this yet, so if anyone does before I get a chance, please let me know if it works and or what I should do differently next time. Print instructionsCategory: 3D Printer Parts Summary This is an attempt at creating a cover that...

Cable chain with connectors for the "Y axis" is here: http://www.thingiverse.com/thing:2006598 Cable chain with connectors for the "X+Z axis" is here: http://www.thingiverse.com/thing:2024115 Box pro Arduino Mega + Ramps 1.4. je speciálně navrženo...

I made some crucial adjustments to utilize Ramps 1.4 effectively: I swapped the endstop plug from a 3-pin to a 2-pin configuration, temporarily using jumper wires due to a lack of compatible connectors. To ensure compatibility with the Ramps diagram,...

At the bridge's crest lies a 20 millimeter top layer connecting it to both the left-hand corner with a lengthened factor board attachment, secured by four screws measuring 4.4 mm in diameter and arranged around each of two separate mounting...

http://www.thingiverse.com/apps/customizer/run?thing_id=861360 Using the Following Settings: Factor Right: Set to 3 Fan Offset Screws: Positioned at 25 Ramps Xtra Front: Not Installed Factor Corners: Configured for 3 Metal Screw Length: Set to 30...

http://www.thingiverse.com/apps/customizer/run?thing_id=861360 Instructions Using the following settings: Factor board mounts: 3 units Fan diameter: 60 degrees Factor bottom: 3 units Factor front: 3 units Resolution: 0.4 millimeters Fan offset...

http://www.thingiverse.com/apps/customizer/run?thing_id=861360 Instructions Using Options: Ramps Extra Front Height 0 Mm Ramps Extra Left Height 0 Mm Factor Back Panel 3 Times Larger Than Standard Ramps Extra Back Height 0 Mm Factor Boardmounts 3...

http://www.thingiverse.com/apps/customizer/run?thing_id=861360 Instructions Using the following options: box_hight = 65 fan_screws_d = 4.4 mount_type = 0 single_wall = 0.6 backstyle = 2 ramps_z_spacing = 5 resolution = 0.4 factor_bottom = 3...

To build this project, I leveraged existing CR10 parts, including the Mosfet and power supply, in conjunction with a RAMPS 1.4 board, a Pi Zero W module, and an HP USB power adapter. ...Future updates are planned to further enhance this innovative...

Learning Sketchup is a challenge I'm tackling head-on by reworking the ramps 1.4 box with even more prominent open hardware logos. 7/9/2015 - The design was updated by choosing not to fully extrude the gear on the front face, making it easier to...

This enclosure begins with design and construction as seen at http://www.thingiverse.com/thing:8935, primarily intended for use with the Ramps 1.4 platform. It is adapted to accommodate a compact electric fan measuring 40 x 40 mm. Additionally, two...

I needed a straightforward solution to install Reprapdiscount Hall-O effect endstops on all axes for minimum and maximum settings and integrate my Arduino/Ramps 1.4 along with a voltage step-down module for an 80mm fan on the Y-axis. This is what I...

The included STLs are specifically for a RAMPS 1.4 with LCD board and a 40mm fan mounted on the interior top, with a mounting offset for a SeeMeCNC LaserCut Prusa i3 frame. The SCAD is easy to edit for other setups. This enclosure provides 4 screw...

Mount the electronic ramps to the left side of the Prusa I2 Printer Print Settings Rafts: Yes No None Supports: Yes No None Resolution: 0.1 0.15 0.2 Infill: 10% 20% 30% Notes: Print with PLA

Fan Screws Diameter: 4.4mm Resolution: 0.4 Extra Back Ramps: None Extra Right Ramps: None Fan Diameter: 60 degrees Z Axis Spacing: 5mm Compensate Offset: Off Mount Type: Internal Extra Left Ramps: None Factor Board Mounts: 3 times thicker Box...

This is a simple RAMPS 1.4 case drawn in Freecad. The top locates a 40mm Fan. The bottom is just open, so air and wires are free to exit. The primary problem I was trying to solve was the RAMPS fan causing a draft across the printing bed. This does...

This electronics enclosure, designed for RAMPS 1.4 with a 40mm fan, is compatible with Prusa i3 single sheet frames. It's an improved version of the original design found on Thingiverse (http://www.thingiverse.com/thing:3917), which I highly...

This is a fresh design for both the front and bottom panels of the iPa64's case, tailored specifically to accommodate the Arduino Mega R3 and RAMPS 1.4 boards, as well as the new 2560 Mega board. The updated front panel now features an extra hole,...

ParametersHoles 3.5mm 7.00 mm for the bolt head6.00 mm for the female screw5.20 mm bottom hexagonal (female screw)Fan size:50.20 x 50.20 mm distance between holes mid pointhole size 4.20mm and 6.50 for the bolt headCommutable button panel for extra...

Here's my design for a base mount that works seamlessly with Arduino/RAMPS 1.4 electronics on a Mini Kossel 3D printer. Unimpressed by off-the-shelf solutions from AliExpress, I opted to create one that caters specifically to the needs of my own...

This is a RAMPS 1.4 enclosure built specifically for the Lulzbot Taz 5 3D printer. I designed this custom enclosure when assembling my Taz 5, opting not to purchase the standard RUMBA board included with the printer. Instead, I modified a Ramps board...

Designed specifically to complement the capabilities of a Duplicator i3, this add-on is intended for seamless integration of ramps with diamond hotends, ensuring uninterrupted print operations. ...Please do not initiate printing without prior success...

Instructions Using the Following Options: Fan Screws Diameter: 4.4 mm Layer Resolution: 0.4 mm Extra Ramps on Right Side: Off Extra Ramps on Back Side: Off Fan Diamter: 60 Compensate Setting: Off Z-axis Ramps Spacing: 5 units Mount Type Selection:...

Case for Arduino Mega R3 and RAMPS 1.4 - perfect for Prusa i3 or other DIY projects! Dimensions: 80mm x 140mm x 63mm Designed for parallel printing Secure it all with M3 nuts and 8 or 10mm bolts - don't worry if they slip out of place, we've...

I crafted this bracket to securely hold the Arduino MEGA+RAMPS 1.4 boards and a 40mm cooling fan, then attach it to a steel stand for my QU-BD ThreeUp V2. The files provided include the DesignSpark Mechanical 2.0 file for anyone who wants to remix...

DeStulps created remix 1.4 ramps to fix overheating problems, but I added more vents to the case to minimize static pressure and boost airflow. By reducing pressure, the heating problem disappeared entirely. Attach deckels and frames using M3x8...

... there is a hole for mounting a fan, with fan bolt holes spaced 32 mm apart. **Print Settings** Printer Brand: Prusa Printer: i3 MK2S Rafts: None Supports: Yes Resolution: 0.1 mm layer thickness and 0.4 mm nozzle size Infill: 15% density

This box was designed to fit for Arduino mega + Ramps 1.4. It is complete with its cap with fan mounting holes (40*40 fans) and with the mounting support to fit Prusa i3 Rework frame. USB hole in one side and a big hole for the services cables...

I designed this bracket specifically to hold the Arduino MEGA+RAMPS 1.4 boards and a 40mm cooling fan in place, while attaching securely to my QU-BD ThreeUp V2 steel stand.\nThe included files comprise a DesignSpark Mechanical 2.0 file for anyone who...