raspberry pi 3 b enclosure stl 3d models

... ...The power cable can be clamped down using two M3 x 8 screws. The relay can be screwed down with up to four M3 x 2.5 screws. The Raspberry Pi can be secured with up to four M2.5 x 6.0 screws. ... This case is a snap fit design and has four joins.

I've designed a custom case for the Raspberry Pi, specifically as an all-in-one media center box solution. While similar cases have been developed before, I wanted something tailored to my needs, so I took matters into my own hands and created one...

... through them seamlessly. For optimal alignment of Raspberry ports with the right side panel of the printer, print pi3_box_mount_part2a.stl. ...If you prefer to hide the ports by shifting them 15mm to the left, print pi3_box_mount_part2.stl instead.

I was on a mission to find a compact and robust Raspberry PI 3 case when I stumbled upon jayftee's ingenious creation at http://www.thingiverse.com/thing:1427797 - what a score! However, things quickly took a turn when I realized I didn't have any...

UPDATE 11/09: Added new top part version, with swappable lids.Simple vented, can open up to remove or place ribbon cables on the Pi.30x30 fan mount, 40x40 fan mount.Mount the fans by regular M3/M4 bolts/nuts, depending on your fan size.I suggest...

This a remix from Homwer's 40mm fan mount, for the 30 mm Pi Fan and without the leds and that stuff. This is still a work in progress because the raspberry pi screws are still a little bit tight fit. You can use either M2.5x18 or M3x18 screws so the...

Hello Community, here is my case for the raspberry pi 3b+. ...It is made for two 28mm fan´s. I´ve designd it for my retro pi because i wanted to add two 28mm fan and found nothing similar. The edges for the screws designd for insert a squared m5 nut....

I make the bottom more stronger in before, there are very tight fit if your Raspberry PI don't fit you can scale it to 102 % The parts are held in together by friction. So no need screws in this case. ... New version...

The plan calls for a sturdy raspberry pi rack to support a cluster of Rpi B+ devices, or even to utilize the space as storage. ...It is crucial that each Rpi is secured firmly into place on the specially designed rpi tray that I've also engineered to...

In previous versions, I strengthened the bottom to address issues with tight fits; if your Raspberry PI does not fit properly, scaling up by 2% should resolve the issue. The parts are secured together through friction alone, eliminating the need...

I added tnuts to the side to be able to mount the Pi to the side of my ender 3 v2. I've used this: https://www.thingiverse.com/thing:3050607 but can't link it as remix source files for some unknown reason. No screws needed. The bottom part...

A cabinet for KronBjorn's 6" rack: https://www.thingiverse.com/thing:1936196 Intended to be used with my ATX PSU cabinet here: https://www.thingiverse.com/thing:3352702 Made to house a Pi 3 with an ATX 24 pin power input, I'm intending to power the...

... a high-capacity lithium battery rated at 2500mAh. ...This battery is designed to power the popular single-board computer models RPi 3 Model B, RPi 2B, and RPi A+. ...The ATP (Air Tanker Protection) system ensures safe operation in various environments.

I removed the name etched into this decent pi case, allowing it to be printed in T-glass without displaying someone else's name. ...Check out the original for the top-rated options.

I was searching for a Pi case that could easily attach to my CR-10 without any hassle. Unfortunately, none of the cases I came across met my expectations. I decided to take matters into my own hands and modify Adrian12's case by adding some custom...

I designed a new housing cover for the Raspberry kit after realizing that the supplied fan wouldn't fit properly. The result is impressive - my custom 30x30 mm fan fits seamlessly and runs smoothly without any vibrations. ...In my setup, I had to remove...

I was looking for a Pi case that could easily mount to my CR-10. Nothing I found I liked. I used Adrian12' case and added a couple of mounting brackets to it. I think this will work out just fine. ... Thanks, Adrian12 for a very nice case.

... a straightforward design, incorporating holes in the top plate that will allow me to add a decorative shoelace. ... Get ready by gathering M2.5(10mm) screws to secure your Pi and M3(25mm) screws to hold both the upper and lower plates firmly in place.

Modified the compact case to accommodate the Pi and its ProtoHat attachment, replacing traditional pin supports with screws that secure both components snugly inside. ...Ensured seamless airflow by filling in the fan slot and creating a ventilated space...

################################################## ES: El ventilador suministrado con el kit Raspberry no cabía en la cubierta de la caja, así que decidí diseñar uno yo mismo. El resultado es perfecto, el ventilador de 30x30 mm se ajusta...

To keep everything neat and organized, the bottom of the case needs to be attached to the frame before installing the Pi. Since I had to order screws anyway, obtaining M2.5x16 was not a big issue. ...However, the mount requires M3x8s, which should be...

This is a remix of Sparrows89's amazing Gamecube Pi Classic and TheJeffChen's equally amazing Logo Dunk Corner Stand. I opened the vent holes on the sides and put some holes under the PCB (my Pis tend to run very hot - so I'll take any ventilation...

For those wanting an attachment for a Pi to the new MINI base but not neding to mount he PSU brick. You will ned a USB cable with a right angle end on the mini usb connection.Allows for a 30mm x 30mm fan (3v or 5v), requires various screws 4 to mount...

Despite of the huge amount of ventilation, the Pi still got over 50°C. So a 40x40 fan was put on the front side. ...But it was too high so that the mounting screw was not reachable any more.I moved the case a bit. The cover fits from the original...

THIS IS PART OF AN OVERALL Lack Enclosure design: https://www.thingiverse.com/thing:3129929 Remixed case with a tad more room for CPU heatsink. Added cutout for camera cable and cut at the bottom for soldered/external power output. Cooling ribs...

Top is unmodified from original and included only for completeness. To keep things compact, the bottom of the case must be mounted to the framebefore you install the Pi. I had to order screws, so getting M2.5x16 wasn't a big deal :). The mount...

This is a remix combination tool holder and Raspberry Pi case which can be printed with the USB ports forward, left, or rearward. Inspired by https://www.thingiverse.com/thing:2675782. ... As always, if you make it, I'd love to see pictures!

Designed specifically for Creality Ender 3 Frame, these lids are a must-have accessory for your printer. I use mine in conjunction with Octoprint for added functionality. Note: To assemble the lids, you will need two M4 sliding T-nuts and two M4...

3. A hidden input field named "business" with value associated with the merchant account. 4. A hidden input field named "item_name_1" with a value, possibly indicating the name of an item being purchased. 5. A hidden input field named "amount_1" with...

Check it out: https://www.thingiverse.com/thing:5215750 I dont have a RP4 yet, so I changed the design to fit a 3 or 3B+ version. I uploaded two models: the one I am working on, it has just a USB to power and a RCA conector to output video. The...