raspberrypi logo 3d models
82923 3d models found related to raspberrypi logo.thingiverse
Raspberrypi logo with openscad source I used it as ornament on my case.. And there are 8 spacers in there as well that i needed. . ....
thingiverse
RaspberryPi 3 case with ender text RaspberryPi 3B+: Works perfectly. RaspberryPi 3B: Works perfectly. RaspberryPi 3: Works perfectly. RaspberryPi 2: Should fit. Feedback? ... RaspberryPi B+: Community reported that it works.
thingiverse
i printed it with thermo-active PLA from "das Filament". ... The picture was taken with rpi3 in idle, but during heavier load it becomes completely white please take the bottom part from the design by jegi: https://www.thingiverse.com/thing:1956623
thingiverse
This is a simple stand for RaspberryPi model B, compatible with any generation I think, the holes should be in the same. ... It is great to simply lift the board, increasing cooling and to sit more firmly on the working table.
thingiverse
... Android). ...Runs on a Raspberry Pi connected to an Arduino Nano with shield Find code and Assembly Instructions here: https://github.com/LakshBhambhani/RaspberryPi-Minikame Also, instructable on: https://www.instructables.com/id/Raspberry-Pi-Minikame/
thingiverse
Simple rack to keep a RaspberryPi off of a workstation. Instructions The arches made this a bit of a difficult print, but I wanted it to look good. I printed this at 75% infill, 30mm/second feed...
prusaprinters
It ads to the snap fit RaspberryPi 4 Model B Case from Malolo a “backpack” that houses a M.2 2242 SSD with adapter and USB 3 connector. It screws on at the bottom of the edited z_bottom_base_sm mesh. i use the RASPI4 for astrophotography and needed...
thingiverse
There are locating holes on the logo pieces that match locating pins added to the case tops. If you're using an easy to glue filament type, add a drop of glue to each pin to secure the logos. My perferred method is to melt the pins to hold the...
cults3d
There are locating holes on the logo pieces that match locating pins added to the case tops. If you're using an easy to glue filament type, add a drop of glue to each pin to secure the logos. My perferred method is to melt the pins to hold the logo...
thingiverse
RaspberryPi Cam Corner support To use with this case:http://www.thingiverse.com/thing:92208
thingiverse
Layer board and a top with the kubernetes logo for creating a RaspberryPi 2 stack. You will need a nice set of 2.5mm plastic / metal spacers with adequate nuts and bolts. Print with a bigger infill percentage to ensure the boards will be strong...
thingiverse
This is an SDCard retainer for the RaspberryPi. ...It will hold your SDCard inserted even if the RaspberryPi is subjected to vibration. ... As always source available on my github: https://github.com/NetForces/Hardware
thingiverse
PiHouse - RaspberryPi + Arduino case Components: RaspberryPi 4 Arduino Pro Micro LLC (5V 3.3 V) 5’’ HDMI screen 20Ah battery A bunch of step-down regulators Power switches 5.5 mm power socket for 12V input Pin sockets and wires
thingiverse
A little case for a SSD and RaspberryPI 3 Together it is my personal NAS with a mysql database. ...
thingiverse
Front and back case for RaspberryPi Camera - use M3-16 Bolts to bolt together. ... Attach to base of 3d Printer using binder clips
thingiverse
It can prevent electric shock between Raspberrypi(3B+ or higher) and Raspi Camera. This is the first version of camera case, version 2 is coming soon. Ps. Each part might not fit. Up to the printer. ...In my case, with Anet A8, I must trim it a...
thingiverse
... pi with a camera and monitor. ... Raspberrypi : RaspberryPi 4B Monitor : https://www.amazon.co.jp/dp/B081Q7Y3JL/ref=cm_sw_r_tw_dp_P9XRY7MSC6E0EH9J0E31?_encoding=UTF8&psc=1 Camera : https://ja.aliexpress.com/item/4000631570932.html Screw : M3,M6
thingiverse
This is a simple omnidirectional bracket for RaspberryPi camera module. ...The project is dedicated to my friends http://raspibo.org and I want to share with all the makers and comunity open-source of the world.
thingiverse
Houses 5 RaspberryPi 4s, an 80mm fan, and an Anker 60W 6 Port USB Charging Station. Requires 4 m3 screws and m2.5 spacers. Why 5? ...That's the minimum for a highly available kubernetes cluster.
thingiverse
A smaller version of the HD Stand, that it suits for the RaspberryPi Case (https://www.thingiverse.com/thing:559858) I've got in my FlashForgeDreamer. ...Just to save space and because the cam-cable is to short ;)
thingiverse
I couldn`t find proper RaspberryPi 4B enclosure, so I decided to design myself. It haven`t been printed yet but I think will fit well. ... It is necessary to have SD Card extender (rectangle hole on top part)
thingiverse
I am using Octoprint on the raspberryPI. If you have a spool on AnetA8 it may be hard to use. ...My spool holder is on a roller so spooler hangs are empty in my workspace.
thingiverse
TimeLapse construction modèle 3D : https://youtu.be/w3-6zvt8i18 [EN] A simple fan support for all model of RaspberryPi 3. He can be installed on or under the card. ...Model of the fan standard (like 3D printer for the nozzle) with hole for screw of 3...
thingiverse
This is a case for RaspberryPi 3B+ and 4*. The covers are snap fit. You can choose from two covers. *** ![covers](https://cdn.thingiverse.com/assets/65/ba/30/0b/56/featured_preview_HiFiBerry_Case_covers.png) *The Raspberry Pi 4 case is a work...
prusaprinters
Printable 40 pin connector for RaspberryPi. You just insert separate cables (goldpin connectors) inside, put locking bar in and voila. You made yourself a working 40 pin connector and got rid of single plug cables. ...Never connect to wrong pins again...
myminifactory
RaspberryPI 3 Case, Small case for Prusa i3 Frame. It did attach to the frame with one screw only, the cover has two hooks to help keep the case centered. ... I did attach two top's, one clear and one with electronic skin that will help cooling.