rat fink models

A STEP file with all the final models is posted here, to make remixing easy. I only ask that if you make a change you like, please share your remix so everyone can benefit. I used Hatchbox Wood PLA for the sides and regular PETG for the other...

The objective is to not create bulky pieces of plastic that distract from the model with the exception of when it is necessary to do so, such as a lift system and a track splitter/track combiner, motor and battery mounts, etc. I will be adding a...

And for many builders I consider this simpler than going the path of printing Flex material.  Model DetailsPulley and Bearing Press ToolThere is not much to say. It shows the pulley with a bearing and heat-shrink tube on the outside. The...

So go ahead and print the firmware appropriate for your printer.icarus-orbiter-1.5-xplus-imate-firmware.gcodeJust place it on your USB stick and print like you would print a normal model. It will make adjustments to the motor directions, X and Y...

 The tire model itself isn't chiral.  The tire part is only chiral after printing with one side down, and only appearance-wise.  Functionally the tire should still be non-chiral until you attach the tire to the wheel at which point the...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Superior...

---- ###Running the Customizer### Thingiverse hadn't run their customizer queue from Jul 10, 2020 to Aug 4, 2022 and may stop running it at any time again, so if they don't process your customized job, you will have to install and run OpenSCAD (free...

It was the perfect model to start with as it was multi-part, required many "sketches" to build and extrude, and it required many different skills to complete. I reference sides in this posting, please refer to the "orientation" image (2nd image) to...

On the X-Max you can have it installed all the time but I'm unsure of the other supported printer models.Print SettingsPrint the carriage in high temp resistant filament. I recommend using Polycarbonate (PC), a PC blend such as PC-FR (flame retardant...

:) There are two variations of the model; one has an additional thin cutting edge that is 1 mm in height and about 0.5 mm in width, so if you have a 0.4 mm nozzle, it will be a single path wide. That's the one shown in the photo. It's probably the...

Like most of the sci-fi and astronomical models of this scale, the topography is exaggerated to make it more visible. Something about the thumbnail image: I generate it using Blender, in which I painted the model, and illuminate the scene with two...

...More importantly, Thingiverse hasn't run their customizer queue since Jul 10, 2020 so until they fix that issue, you will have to install and run OpenSCAD (free software) on your own computer to process the code to create your own customized models.

We don't use the shell.PrintingPrint all models in their original orientations.The faceplate should face down and needs no support. You might want to add a little bit of negative Z offset to this one for a squished first layer on a rough bed for a...

Please check the images to see what's in this kit.This set includes: - Modular Golem Simulacra (6+6)- Auron Lightbringer- Anja Wildarrow- Garrett Shadowgear- Nogroth Doomcaller- Amber Secretflame- Ultran Dragonsmasher- Clay Westwood- Golemhounds (2)-...

Adjust the bed leveling screw closest to where it measures and by the time the script has looped three times the bed will be perfectly level.Copy to your USB and just print it like you would a normal...

I increased the version numbers to reflect this, but if you already printed them you don't need to reprint because there were no actual changes to the models.Added drop-in boxes to fill with cut-off 12in bamboo shish-kebab skewers, to allow for...

I did not contributed on doing the original file from the collection of asteroid radar models of the PDS site, I just simplify and softened it using Blender. The file's names explained: name_1_x_10_y.stl is 1 : x * 10y. So _1_6_10_7 is 1:600000000 or...

For the Dual Module the WAGOs are also an easy, soldering free option to combine the cables from both fans.________________________________________________________________________________________________________________ AIMReduction of volatile...

This model includes a 14T pinion and a 46T crown which can do a great combination for a start point. The second reduction is between the main axle (previous crown transmits its turn to this axle) and the rear wheel with a belt system. This, the belt,...

So go ahead and print the firmware appropriate for your printer.icarus-orbiter-2.0-xplus-imate-firmware.gcodeJust place it on your USB stick and print like you would print a normal model. It will make adjustments to the motor directions, X and Y...

(6 pieces I think)If you build it all on your desk before touching a single bolt on your printer, you will see where these parts are working together.I will post up some tinkercad screenshots as a kind of airfix model instruction exploded diagram...

I also like to print model airplanes, and deltas are easy to make taller. Thus a delta with 350mm diameter bed, and 1 meter towers. Print volume is 350mm diameter by 440mm tall. You can fit a 230x230mm square on the plate and have a bit of room left...

(earlier X carriage design that was sloppier than the current version) Deleted all the rsdoc files and uploaded them all in one zip, this also has assembly models that do not have stl's. Added some screencaps as they may come in handy if...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 347-480V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Wiring & Plug: This explosion...

This model includes a 14T pinion and a 46T crown which can do a great combination for a start point. The second reduction is between the main axle (previous crown transmits its turn to this axle) and the rear wheel with a belt system. This, the...

So go ahead and print the firmware appropriate for your printer.icarus-sherpa-mini-r1-xplus-imate-firmware.gcodeJust place it on your USB stick and print like you would print a normal model. It will make adjustments to the motor directions, X and Y...

I have to clarify that non feature shown in the model have a real correlation, the material there is orbiting in a thin flat disc around, and from 3 times the Schwarzschild radius beyond. The main brilliant ring is the photon ring, composed of...

BETAFPV LiteRadio3 Controller - ELRS Model On the one hand you don't want to skimp, it's your means of controlling your drone. On the other hand traditional radios are bulky, heavy, and seem to be overkill for me. Got a drone with an ELRS radio? Get...

Here is a link the the Prusa GitHub where you can download the latest firmware for your model of Prusa printer. https://github.com/prusa3d/Prusa-Firmware Instructions on how to compile and flash the firmware to your printer are not provided...

Adjust the bed leveling screw closest to where it measures and by the time the script has looped three times the bed will be perfectly level.Copy to your USB and just print it like you would a normal...