rc rcx 3d models

360-Degree Antenna Tracker Design for Aeromodelismo Virtual Project Developed on the Spanish RC and FPV Forum Link to Development Thread: http://www.aeromodelismovirtual.com/showthread.php?t=34530&page=168 This design is based on a German project...

This is a replacement battery hatch / cover for the Max Thrust Riot or the ArtTech Devil RC model aircraft. The original hatch is curved to match the profile of the fuselage, but in order to make it simpler to print and to limit the amount of support...

The drive uses two 25 tooth, 5mm shaft gears (RC cars parts) for the motor to drive a layshaft that runs in in brass tube bearings in the PLA frame. This shaft carries two 9 tooth Meccano sprocket wheels driving chains down either side to two much...

RC Crawler tire foam. Great sidehill stability. Different sizes and specs will follow. Printed with TPU ------------------------------------------------------------------------------------------------------------- Parts for 2.2 to scale...

It also happens that using an M5 tap on the top inlet hold of the spindle assembly will allow you to easily thread insert and obtain a strong fluid seal into the spindle body with a M5 hydraulic fitting like...

**Maximum handlebar diameter of 26mm** Required/Recommended Filaments: **Flexible Filament** - Harness, Phone Pad, Bar Pad, Ripcord - .2mm LH **ASA** - Upper, Lower, Clamp - .3mm LH All parts are oriented as they should be printed **Harness /...

Next, I organized the "Rainbow Crossing" (RC) box so that it would fit sleeved cards. Further, I wanted to store the "Kickstarter Upgrade Pack" (KUP). You can ditch the clear mini trays from Rainbow Crossing and print the spacers (0 top and bottom...

Hardware Shopping List BOLTS M3x18 x7 M4x20 x1 M4x50 x1 M4x65 x1 M6x35 x1 M6x50 x1 M6x155 x1 (threaded rod) NUTS M3 half hex x 7 M4 Lock x6 M6 Hex x4 M6 Lock x2 Bearings ID-4/OD13 x7 (ebay) ID-6/OD15 x4 (ebay) ALUMINUM EXTRUSION 12x12x1.4 U channel...

Instructions These are designed around the Common Sense RC-35 Ultra-Nano Servo. They're small cheap and strong The 6X9 Robo-Shutta uses small plates and 3mm bolts to clamp the servo in place For best results tap threads in the mounting holes. The...

The camera is this one: https://www.ebay.com/itm/263827304354 LED light: https://www.banggood.com/12V-Motorcycle-Handlebar-LED-Headlights-Running-Spotlight-BlueGreenWhite-p-1279313.html?rmmds=myorder&ID=233&cur_warehouse=CN LED light switch:...

... Be sure to visit my gallery "Efran", to see the other pilots I have, I'm sure they will be of great help to your projects, be it RC planes, games, comics..anyway, imagination sets the limit. leave me your comments, I'm always ready to answer you.

For more info about the F1 car release and Open-RC projects, head to http://danielnoree.com/. For OpenR/C Formula 1 print-files (after release), visit https://pinshape.com/users/18846-danielnoree. My designs can be found at...

Bei "Pollin" habe ich einen Servotester(Bausatz) zur manuellen Steuerung(ohne RC) gefunden, mit dem ein Servoweg von 180° erreicht werden kann, was mit einem "normalen" Empfänger nicht geht: https://www.pollin.de/p/bausatz-servomotor-tester-810201...

Supported Frames: - Airflex FlexOneV2 - Amax F5L - Amax F5P (old) - AOS 3.5v2 - AOS 5/5.5/7 - APEX 5inch clone - APEX 3inch clone - Armattan Beaver - betaFPV x-knight35 - Botgrinder Demibot - DavideFPV D-Rockv2 - Diatone Roma5 - Diatone Tycan -...

I needed a clamp to reach deep inside my RC aircraft frame, and this worked out perfectly. It's based on a 3/16 square brass tube (K & S #8153) and a 6-32 threaded rod, both of which come in 12-inch lengths. I cut them in half to make a pair of...

Part cover.stl is a door where I have made holes for 12mm inductive sensor (LJ12A3-4-Z-BX NPN) wire(mounted with zipties to droptube), a on/off switch and 5.5*2.1 chassis mount socket and a PWM speed controller Socket:...

I used the following parts for my build: * [Beta65 Pro Frame](https://betafpv.com/collections/brushless-frame/products/beta65-pro-micro-brushless-whoop-frame) with the [low profile mod](https://brushlesswhoop.com/beta65-low-profile-mod/) * [BetaFPV...

A Cub-style landing gear I designed for an RC DIY bush plane I built, boasting a wingspan of 120 cm and a total weight of approximately 1 Kg. However, this landing gear can easily be adapted to fit planes that are both smaller and larger than mine. ...

Part list: - 27mm Dressmaker Pins - 4x TT motors - 4x RC servo screws - Elastic rubber tube (Inner diameter: 2mm, Outer Diameter: 5mm, cut to 22mm length each) https://www.aliexpress.com/item/32826819065.html?spm=a2g0s.9042311.0.0.27424c4dxN6rvZ...

I have purchased a few RC Tanks from "Heng Long" (Tiger I, Tiger II, and a Jagdpanther) as well as some Tamiya Epoxy Putty (Quick Type) to add miniature welding beads around the parts on the tanks. This gives the model a more realistic look after it...

*** Last Update (21.08.16) *** Joined 3 locks into 1 part for easier printing Use brim option to minimize any errors during printing Just incase if you are not accessible to 3D printer, you can buy the printed part from my shapeways shop below :...

I've been working on modeling and printing this 1:10 scale overland or utility type trailer for RC models. I am calling it the "Goodson's Hobbies Scaler Trailer" or GHST for short. I've been working on this as a fun project that I thought others...

To explore other innovative designs, visit the following links: * UMC - Universal Motion Controller: https://www.thingiverse.com/thing:4245315 * 3D-printable Davinci Catapult Gift Card: https://www.thingiverse.com/thing:4067668 * Arduino-controlled...

For the most up-to-date parts, visit the GitHub project page. A 3D-printed, 4WD RC drift car. 1:28 scale, fits 90mm (M) wheelbase MINI-Z shells.</h3> <h3>Test drive: <a href="https://youtu.be/90DoZpYbfy4">https://youtu.be/90DoZpYbfy4</a></h3>...

STARTING POINT This is the foundation of the M548 RC 1/10 scale model's Wheels and Suspension. After putting it to the test, I'm pleased to report that it functions properly, although some finishing touches are still needed. You can see it in action...

The ball bearings increase the life of these fans through rough driving conditions and dirt: https://www.amazon.com/gp/product/B07KRST21P/ref=ppx_yo_dt_b_asin_title_o03_s02?ie=UTF8&psc=1 In addition, I simply used excess hardware from RCscrews for...

There is JST RCY (so called BEC connector) to connect common RC charger to recharge the battery. But this will be needed hopefully once per two years or so.</p> <p>There is small DC/DC supply of 12V for 3.5" disk.</p> <p>Dual Schottky diode is...

Sayha FPV Race Frame This quadcopter frame is based on the Impulse RC Alien and Lumenier QAV-R with center X removable arms. It comes in various sizes that support 4", 5" and 6" propellers. When printed in ABS 100% infill, it's incredibly light and...

... motors were employed. This entire project is controlled using my Smartphone and the Bluetooth RC App, which connects to the HC-05 bluetooth Module. ... An Arduino UNO with Dual Monster Moto Shield (VNH2SP30) was utilized to control the motors.

RC car tires would probably look great.\nTo assemble, print the wheel of your choice and the connector housing. Use support material when printing the wheel to fill in the well for the connector. Fit the washer into the connector housing. Then press...