rc snow mobile 3d models
61736 3d models found related to rc snow mobile.cgtrader
This is a future snow mobile design with areodynamic shape. ...
prusaprinters
... of my complete RC snow blower assembly. ...It was originally designed to fit with the Traxxas Summit RC car. However, I would recommend a larger RC car because the snow blower is to heavy for the Summit.Here are a few videos of it in action:
thingiverse
Snow Skis for an RC Plane. These are about 7.5 inches long as printed. The scad file is poorly commented and I am a hack coder so if folks show interest I will comment it further. There is a scale function at end of code allowing you customize in...
thingiverse
It should fit most electric RC airplanes with tricycle or tail dragger front wheels in the same 1/8 in. wire wheel struts. The file with skig is for the front steering wheel. After printing you will need to heat up the front part (first 1 in.) of...
pinshape
It should fit most electric RC airplanes with tricycle or tail dragger front wheels in the same 1/8 in. wire wheel struts. The file with skig is for the front steering wheel. After printing you will need to heat up the front part (first 1 in.) of...
thingiverse
... Video of the tracks in action: http://youtu.be/Olw4WwAe8B8 Instructions To make 4 Snow Tracks you need: (2) Tamiya 70100 Track and Wheel Sets. You only need the tracks and the axles, you can discard the orange wheels in the kit. (8) 6204 Bearings.
thingiverse
I made these weird-looking one-piece snow wheels to help add a bit more traction to my Traxxas Rustler VXL when I want to do low-speed runs in snow and possibly in the sand. ...I plan on using them to make a stupid-looking snow plow set to clear an inch...
thingiverse
this is a snow plow im planning on using this season for a 1/10 scale rig with a wedge shape. i have not tested this plow and am still working on the connecting bracket. this print is in 2 parts for smaller printers. i have 2 small pegs on one of the...
thingiverse
I Made a ski for a couple of my rc planes. The many holes in the mounting plat is for adjustment. The holes are 4 and 5mm. I will be changing this as I print them and test them. To print I scaled mine down by 0.9 My planes can't take off with...
thingiverse
The landing gear on the sport cub is ok for the skis on snow, but it has a tendency to dip the nose on take off. Speed is your friend and always keep plane into the wind. I used rubber bands to keep ski tips up. You can attach the rubber bands...
thingiverse
I live in Maine, so flying in the wintertime means snow. Obviously, skis had to happen. I've tweaked these to the point that I'm pretty happy with them. They look scale-ish and fly well. The only thing I'd say is that when landing, you might need...
thingiverse
This is a snow plow for a very small scale RC car and the attachment may not work on all RC cars.
thingiverse
Snow shoes for rc heli Fits Raptor skid tubes Small hole to tap 3mm grub screw to secure in place
thingiverse
... Noree's Open rc f1 car. ...It includes snow tires for the rear wheels and skis for the front. It's really simple but a lot of fun. Watch it drive and the build guide here: https://www.youtube.com/watch?v=cii2E4xWl5k Happy Printing! .../3Drcnc
thingiverse
Made some snow skis for the arrows rc bigfoot. I usually don't make a tail ski anymore since it just drags in the snow like the wheel does. Just print 2 of these skis, they are the same for left and right. After you print them, you will make...
myminifactory
Did you ever want to drive on snow or ice with your RC-car? With this design you will be able to drive on rougher and slickier terrain! Just print out the part as often as you need it (I needed around 20 of them per wheel with a diameter of 10 cm).
thingiverse
... first one. i deleted the first ski and replaced it with an updated version that is more balanced. I deleted the The P2 part and replaced it with a part that uses the factory nut on the RC car on the axle shaft (the first one wasn't set up that way)
prusaprinters
It includes snow tires for the rear wheels and skis for the front. It's really simple but a lot of fun.</p><p>Watch it drive and the build guide here: <a...
thingiverse
RC Snow Tracks for 1/10 scale models. It should fit any car with a standard 12mm Hex Wheel Mount but you might encounter problems with body rub. (Only tested on Axial Capra) Video : https://youtu.be/1Dnh0IAAjnM Google drive link containing :...
pinshape
Next I slightly modified the existing Open R/C Formula 1 rear chassis created by Daniel Noree To except the new sand and snow paddle tires. They are designed to fit the original F1 rims or any of My race rims These new paddle tires will blast you...
thingiverse
12mm hex snow/sand paddle wheel. Modeled based on stock Traxxas slash wheels. If printing with TPU or similar, make sure to print the separate insert and washer out of a harder material (PLA). The hex of the single piece model will probably strip...
thingiverse
This is a remix I made of totofendt snow tracks with a few changes/additions; 1. Uses 6003 bearings (17x35x10). You could still print a bearing if you wanted a printable one. I found printable bearings and grass/dirt don't nix well. 2. Added...
thingiverse
Designed a multi-piece Snow Ski design that uses 2 parts that are repeated in design. No need to print a left side and a right side separately. Break the ski? Reprint the bottom portion instead of a single one piece unit. The base ski has...
thingiverse
Snow and Ice conversion for RC cars and trucks To be used with a 12mm hex hub tires are directional 108mm Diameter 40mm Width can be used on 4x4 RCs Skis are for if you have a 2wd RC 235mm Length 30mm Width I have provided one side and will have to...
thingiverse
These tires are designed for use on any 1:10 rc car. ...It should help a lot with traction in the snow. ...If you would like these for a larger scale vehicle, message me with the shaft dimensions and I can get that made up.
thingiverse
for use with rc snow track Champagne Yeti track this link use less of material TPU and more lightweight can be linked with nails of finition 16 ga 2 1/2 length or for not so powerfull truck like as crawler 1/10 with stock motor you can use carbon...
thingiverse
Skis that can be 3D printed and used on RC planes to fly off the snow. Only tested on a tail dragger but should work for 3 wheeled model planes as well. A few different options were uploaded. Skis with and without directional grooves as well as two...
thingiverse
Hello ! ... I´d created Snow Wheels for my monstertruck and Crawler. They´ve got a 12mm hex. Outer diameter: 120mm Width: 60mm If you like it and enjoy, please leave a "like" - it will mean much to me! ... Thanks !
cults3d
This is a plow for the Aliexpress RC wheel loader. ...This plow is designed to attach to this loader only as the mounting is set for this machine.