rcgroup 3d models

...Thanks ExtremeSports from RCGroups. There are many other tweaks awaiting your testing like G-codes for LW-PLA and an EDF cover with a bit more room for the wires. Please note though that we cannot support these additions as easily as the base STLs.

RCGroups thread: https://www.rcgroups.com/forums/showthread.php?2992513-AeroFred-Das-Liddle-Stik-3D-Printable Updated Updated on 30.11.2017 Added wing servo covers STL, GCODE, .factory Added Torque compensated motor mount 2.5 degrees down and 2.5...

Inspired by the RCgroups forum thread as regards weight reduction. Based on covering with foamboard or foam sheet + wing tape. Basically these are airfoil sections and accompanying aileron and servo bits. These will fit on the Body lid using the...

Build Thread: https://www.rcgroups.com/forums/showthread.php?3104321-AeroFred-Swamp-Buggy In page 3 there is a wooden hull that can be cut with a CNC router, the DXF files are available to download. Hull length: 700mm Hull width: 240mm Print...

Build Thread: https://www.rcgroups.com/forums/showthread.php?3104321-AeroFred-Swamp-Buggy In page 3, there is a wooden hull that can be cut with a CNC router. The DXF files are available to download. Hull length: 700mm Hull width: 240mm Print...

I have the 4in1 multiprotocol module as shown in this thread: https://www.rcgroups.com/forums/showthread.php?2165676-DIY-Multiprotocol-TX-Module from Banggood:...

However, within time, fellow modellers in RCgroups forum requested from me to modify the design to fit their specific setup and the number of files and combinations has increased since then. Currently, three and four-bladed spinners are available for...

Needed Hardware: 1.5x450x200mm Carbon Fiber Sheet 8x Hex Threaded Standoff M3x12mm 4x Round Threaded Standoff M3x20mm 24x Screw M3x6mm (for all Standoffs) 8x Screw + Nut M3x6mm Nylon (for FC and PDB/OSD) 6x Screw + Nut M2x6mm Nylon (for FPV Camera...

For more information, check out this blog post: https://www.rcgroups.com/forums/showthread.php?3321299-VQ-110-B-24-rolling-bomb-bay-doors As of now, I haven't decided how to gear the center rod yet. I'll take some measurements and determine the...

... console, I recommend visiting your local forum on aircraft modeling. There, you can easily find a guide on how to set up the remote control. You can also visit the international forum: http://www.rcgroups.com/forums/index.php for more information.

If you're using QLRS, I've included two boxes: small (LED, button, and 1W module with heatsink) and bigger (http://forum.rcdesign.ru/f90/thread512643-75.html#post7894043 and https://www.rcgroups.com/forums/showpost.php?p=43832375&postcount=3589). To...

https://static.rcgroups.net/forums/attachments/3/9/3/8/8/6/a7856168-100-IMG_20150504_231729.jpg I really thank him for his design and STL file that I used to create this gearbox to be 3D printed. Today, I did the first test drive, and it's driving...

Initially, it was created for Ramoser Varioprop 12C three-bladed propeller, but fellow modellers on the RCgroups forum requested modifications to fit their specific setups. As a result, I have developed different versions to accommodate various motor...

... or visit RC groups for further discussion. https://www.rcgroups.com/forums/showthread.php?3982455-Kougar-Mark-III The included files are STL, 3MF, G-Code, Simplify 3D Factory files.

This is the part where I thank people who inspired me on this fool's errand: DroneMesh's YouTube channel and RCGroups Forum for giving me the idea to do this in the first place. ... Lishy - for the EV100 case model that I used as inspiration for my...

Multi-Part Print, 700g of filament. Very Gentle stall characteristics, high stability, large speed envelope, and top speed with recommended electronics of near 100mph. Print instructionsI know this is a long bit of text, but unless you're...

If you would like to support the project more, you can donate to the Paypal Link here Additional information on RCGroups! Lastly, I want to thank all my Beta testers for the invaluable information they provided along the way. These designs are...

More informations https://www.rc-network.de/threads/andreas-delta.11822532/ https://www.rcgroups.com/forums/showthread.php?3754295-Andreas-Delta Specifications airfoil: NACA 0006 wing span: 1100 mm wing chord: 680/200 mm CoG: 460 mm from rear...

For any questions and assistance please use the RC-Group thread:https://www.rcgroups.com/forums/showthread.php?4036507-Curtiss-P-40-Warhawk-600-800mm-LW-PLA-%28L3D%29 PARTS LINKS X1 A2208 1400KV Brushless Out-Runner Motor (or suitable...

For any questions and assistance please use the RC-Group thread:https://www.rcgroups.com/forums/showthread.php?4021281-Macchi-C-202-Folgore-205-Veltro-warbird-600-800mm-LW-PLA-%28L3D%29 PARTS LINKS X1 2205 2300KV Brushless Out-Runner...

For this build I made use of the v332m main board, with V25E square motor drivers and V2.11 IMU Wiki Page - Detailed instructions and manuals written by OllieW on how to use Storm32 and its basics and Essentials. RC Groups Discussion Page - Mention...

For specific RC related, or even printing questions for the model, please refer to this forum build thread: https://forum.flitetest.com/index.php?threads/36-northern-pike-3d-printed-cuda-clone-it-flies.54579/...