redcat sixty four 3d models

Redcat Everest Gen7 Gear Cover V1 Including Mount ATTENTION: Stock Rear Links Position Not Supported; V2 Does. Like Axial's, A Fully Closed Gear Cover Is Desired. This is a fully closed gear cover with a mounting plate attached. The mounting plate...

These mounts are engineered specifically for use with Goodson's Hobbies custom bumpers.\r\n\r\nThey're designed to be mounted on the Redcat Racing Everest Gen7 frame rails and can be adjusted using the 4 available mounting screw...

Get rid of the velco body mount on your Redcat Gen 8 Scout II, I say! It's time to upgrade. I've taken inspiration from those magnet mounts that are all the rage and designed my own custom holders. Using 15 x 3 mm magnets per holder, two of them per...

Gear Ring uses: Qty 2: M4 Square Nuts Qty 2: M4 x 20mm Socket Head Cap Screws EAF mount is attached between the Redcat and Dovetail using: Qty 2: M6 x 50mm Socket Head Cap Screws and 1 M6 x 15mm Socket Head Cap Screw with M6 Nut There are 2 AIR...

They come in two parts and are perfect for RedCat Racing short course or buggy models equipped with original tires. Since the standard 1/10 size rims aren't available, these custom rims take their place, offering a significant improvement over the...

Crafted specifically for the RedCat Racing short course original tire, they address the issue of non-standard 1/10 scale size and subpar quality of the original rims. An additional rim features a robust 12mm / 6mm hex design with reinforced spokes...

Here's what you're going to do: print out a wheelie bar for your Redcat Volcano Epx Pro. Make sure to print two wheels, and don't forget that you'll need two screws to secure them in place. I like to print these standing up on the small end with...

I made these for my Redcat Tornado EXP as I hate body clips and while magnets work they aren't strong enough to keep the body on during hard driving (aka wipeout). After making many versions I did add some - offset to the thread on the post as the...

Redcat parts on Thingiverse are released under the Creative Commons License Attribution- NonCommercial- ShareAlike 4.0 International (CC BY-NC-SA 4.0). We want to share these parts with the world and inspire people to make and share their own parts...

Redcat parts on Thingiverse are made available under the Creative Commons License Attribution-NonCommercial-ShareAlike 4.0 International (CC BY-NC-SA 4.0). We want to share these parts with everyone, and we encourage people to create and share...

#####Redcat parts on Thingiverse are released under the Creative Commons License Attribution- NonCommercial- ShareAlike 4.0 International (CC BY-NC-SA 4.0). We want to share these parts with the world, and we want to inspire people to make and...

Redcat parts available on Thingiverse are released under the Creative Commons License Attribution- NonCommercial- ShareAlike 4.0 International (CC BY-NC-SA 4.0). We want to share these parts with everyone, and we hope they will inspire people to...

These are detail pieces for the front of the Redcat Gen7 which replace decal headlights and grille with parts that have some depth and can also accept 5mm LEDs for real lights. They go well with my baja bumper design. There is a backing plate that...

Designed this to mount a 1/6 scale Grave Digger shell on my kids RedCat Everest 10 Crawler. It uses the built in body mounts of the shell and Everest. No modifications needed on either. You will need some screws/nuts to mount the shell to this mount....

#####Redcat parts on Thingiverse are released under the Creative Commons License Attribution- NonCommercial- ShareAlike 4.0 International (CC BY-NC-SA 4.0). We want to share these parts with the world, and we want to inspire people to make and...

Human: Remix of Redcat's original Everest 7 inner fenders. Check it out at https://www.thingiverse.com/thing:2584736. These modified inner fenders are made to fit the SPORT model better than the PRO model. Rear Inner Fender: When I printed and...

Redcat Everest Gen7 Gear Cover V1 with Mount ATTENTION: This gear cover does not support the stock rear link position, but a new version, V2, is on its way to address this issue. The design requires a fully closed gear cover like those found on the...

Redcat parts on Thingiverse are released under the Creative Commons License Attribution-NonCommercial-ShareAlike 4.0 International (CC BY-NC-SA 4.0). We want to share these parts with the world, and we want to inspire people to make and share their...

Redcat parts on Thingiverse are released under the Creative Commons License Attribution- NonCommercial- ShareAlike 4.0 International (CC BY-NC-SA 4.0). We want to share these parts with the world, and we want to inspire people to make and share...

I liked the original Redcat version better, with that you also get the two rear mounting holes for the battery tray. On drozd79's version these were gone. You need support only under the two "bridges". Cura adds support under the small bosses in...

However, there's still a issue with the brackets - not all screw holes fit properly on the Redcat frame. ...If you need compatible parts, I recommend checking out these designs on Thingiverse: * https://www.thingiverse.com/thing:690366 *...

These are a DIY kit for installing working tool boxes on the new Redcat Racing 1963 Chevrolet COE Hauler.   Features 3 side tool boxes that open and close and use magnets for locks.  You will need the following to complete: 24 x M3 x 10mm flathead...

For various reasons, not the least of which is creating R/C scale Halo Warthogs, one may wish to add steering control to the rear of a Redcat Racing Gen8. Here I'll attempt to illustrate two different methods of achieving this feat. Neither of these...

These parts are designed to expand the wheelbase of the Redcat Gen8 chassis. This reduces the likelihood of rolling and also increases the space between the steering link and the tires. By default, the links rub on the front tires unless you screw...

Spare tire carrier for the Redcat Gen 8. I included two versions of the carrier, one with a hex to fit the stock wheels and another that will allow you to bolt a Bead Lock wheel without the center hub for a more scale appearance. I also included two...

... For the steering tie rods i swapped out one side with redcat volcano tie ends to make up for the toe correction. - i do want to make up my own version of these to be added to the kit instead of needing to take apart another rc or order extra parts.

To accomplish this conversion, you'll need four M3 set screws measuring 15-18mm (for attaching lower links), four M3 screws approximately 12mm long (for attaching the skid to the frame), and four M3 flat-head screws around 16mm in length (for...

Place the four 3x8mm machine screws through the mount into the holes at the top of the cross brace between the shock towers. 2. Install the internal spooled servo winch servo using the 4 - 3x4mm button screws, ensuring that the winch line feeds off...

This sleek wine glass design revolves around a twenty-point shallow star shape, delivering an upscale visual experience every time you lift it up.\n\n Alongside the OBJ file, the STEP file contains precise vector data that accurately replicates the...

The CASAMANIA model features high detailed design, encompassing all textures, shaders, and materials for seamless use in your scene. This model is sourced from Archmodels vol. 72. It comes with various formats including 3ds, dxf, fbx, max, mxs, obj,...