reloading 3d models

This is a jig that I use to help re-load primers. This particular one is for small pistol primer, I don't use all 100 at once because I ran into issues when I do that. But You can easily use less spots. ... Video can be found here:...

Created a Lee Die Spanner for tightening of Lee dies. ...

A funnel for pouring powder back into it's container. It has a large through hole for fast pouring. Fits multiple bottle sizes. ...Sets flat on the bottle mouth.

# Shell_Load-powder-measure The Shell Load powder measure packs unparalleled powder-measuring accuracy in a compact package. The Shell Load is an effective, accurate powder-measuring tool. The accuracy is between 0,02 gn - 0,05 gn with fast dosage...

Customized version of https://www.thingiverse.com/thing:260104 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=260104

Wanted a quick way to test rounds off of a progressive press to make sure that I didn't have any fail to drop powder. Print both pieces and then use a 1/4 20 bolt in the back and a few washers to get the scales right to where a full load will tip it...

A personalized adaptation of http://www.thingiverse.com/thing:260104 was made using the Customizer tool (http://www.thingiverse.com/apps/customizer/run?thing_id=260104). ...It features 5 rows with 2 pixels of padding, a diameter of 10.2 and a height of...

Customized version of http://www.thingiverse.com/thing:260104 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=260104 Instructions Using the following settings: Diameter is set to 10 units Number of...

Customized version of https://www.thingiverse.com/thing:260104 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=260104

Customized version of https://www.thingiverse.com/thing:260104 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=260104

Customized version of https://www.thingiverse.com/thing:260104 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=260104

Customized version of https://www.thingiverse.com/thing:4830571 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4830571

Customized version of https://www.thingiverse.com/thing:4830571 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4830571

Round capacity increased by hundred percent, a 900-round 9mm ammunition holder

Spline drive lock nuts - designed for use with Lee spline wrench Locking version requires a #2-56 screw; I've only tested with 1.5mm screws so far. ... If any of my designs prove helpful, a comment is appreciated and tips are always welcome.

I sketched out the design to provide a 1 millimeter clearance all around each case so it fits several calibers, including 25 rounds.

Hello everybody, I'm excited to share my first design on Thingiverse. This custom holder is designed and crafted to securely store shell holders of various calibres. Below, you can easily write or attach a label for each caliber. ...You'll find two...

A personalized adaptation of http://www.thingiverse.com/thing:260104 was created using the Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=260104. ...To customize this design, set the height to 10, diameter as 10.2, have 10 columns...

I did a box for two dies side by side with their locking rings "together". I figured by "top and tailing" them the rings would be offset and so It's be smaller and uses less filament. From there it was an easy step to parameterize the whole thing. ...

Customized version of http://www.thingiverse.com/thing:260104 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=260104 Instructions Using the following options: number_of_columns = 5 height = 9 ...

Featuring double-sided design, this tray boasts two sets of holes - one at 0.43" and the other at 0.48". ...Suitable for ammunition ranging from .32 to .45 ACP, note that it may require some adjustments when printing on an 8x8 bed oriented sideways.

Here are trays that will cover holding any caliber from 32 ACP through 45-70. Each one holds 50 pieces and the holes all have a .750 inch spacing between centers. The overall sizes vary based on the diameter of the cylinders, but they're all around...

A Unique Arrangement of Grid Blocks Inspired by a Creative Resource: http://www.thingiverse.com/thing:260104 Generated with a Powerful Tool: http://www.thingiverse.com/apps/customizer/run?thing_id=260104 Building This Project To...

Created with Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=260104 Instructions Using the following settings: padding: set to 1 number of columns: set to 10...

Customized version of https://www.thingiverse.com/thing:4830571 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4830571

Prints seamlessly with both PLA and ABS materials, offering flexibility in choice. Printing without supports is entirely feasible; I successfully produced multiple units without any added support structures. ...The design has been meticulously revised...

Works seamlessly with both PLA and ABS materials. Printing without supports yields successful results, as proven by numerous prints completed without any additional structural elements. ...Measurements are now optimized for metric systems commonly used...