reloop turntable dust cover 3d models

Dust cover for Reloop RP7000 turntables. ...The turntable dimensions are 458mm x 354mm and about 60mm from the surface to the top of the tone arm so this case should fit on turntables with similar dimensions.

Dust cover hinges for LP turntable

I designed this to replace a broken dust cover hinge on someones turntable.

... and vinyl records tend to attract dust. ... I created this simple cover to put in the place of a record when the device is not being used, to prevent dust falling on the surface that makes contact with the record. ... The cover has a diameter of 30cm.

This requires: * Technics SL-1200 MK5 turntable * [Reloop Dust Cover for Reloop RP2000 and RP4000](https://smile.amazon.com/gp/product/B0000WRM2C) * 4x M3x10mm socket cap machine screws * M3 tap (to tap out the un-threaded hinge mounts on the MK5)...

I found the Dust Cover for Reloop RP2000 / RP4000 Turntables described as the perfect size on a few forums and they were correct, the hinges line up. The holes are spaced 43mm apart for the Technics SL-1600, see part dimension dwg. I used the...

This is an adapter which allows you to replace a Technics SL-1600, SL-1700 or SL-1800 dust cover with a new Reloop 1000/2000/4000 dust cover. You need to replace the Technics hinges with the Reloop ones, and you can attach them to your Technics...

It may work for other SL-1200 versions, but I don't have any to try it out on. This requires: Technics SL-1200 MK5 turntable Reloop Dust Cover for Reloop RP2000 and RP4000 4x M3x10mm socket cap machine screws M3 tap (to tap out the un-threaded hinge...

Reloop RP-7000 DJ Turntable

This is an adapter which allows you to replace a Technics SL-1600, SL-1700 or SL-1800 dust cover with a new Reloop 1000/2000/4000 dust cover. You need to replace the Technics hinges with the Reloop ones, and you can attach them to your Technics...

Replacement hinge for Teac TN turntable dust cover. ...The stock part tends to break due to the force of the spring.

This dust cover hinge will work with some of the smaller Dual turntables (1214, 1216) in United Audio bases. Modeled by my daughter. ...I'd never have the patience.

Fluance turntables come with very nice hinges, but you can't use them if you want to take your dust cover off every time you drop the needle on some hot vinyl. ... These standoffs will allow you to go topless whenever you like, but keep your top on...

... the dust cover to close on its own.. I ended up putting the arm on the inside of the dust cover on my turntable, as the edge of the dust cover is flush with the side of the base, but you may want to put it on the outside depending on your design.

This is an adapter to be able to replace a Technics SL-1300, SL-1400 or SL-1500 dust cover by a new Reloop 1000/2000/4000 dust cover. I took JBuschhoff's design for the SL-1600 and lowered the screw holes. Now it fits perfectly for my SL-1300. I...

This is an adapter to be able to replace a Technics SL-1300, SL-1400 or SL-1500 dust cover by a new Reloop 1000/2000/4000 dust cover. I took JBuschhoff's design for the SL-1600 and lowered the screw holes. Now it fits perfectly for my SL-1300. I...

The Reloop RP-7000 is the solution for all vinyl DJs and DVS users who are looking for a professional high-torque, club-standard turntable with extremely strong motor and a sturdy and indestructible construction. With its classy and scratch-resistant...

A Replacement for the spring-housing/bottom part of my "Technics Turntable/Dust Cover Hinge" that was broken. ... It's just a bit tricky to get the spring inside cause the spring is pretty strong.

A Replacement for the spring-housing/bottom part of my "Technics Turntable/Dust Cover Hinge" that was broken. ... It's just a bit tricky to get the spring inside cause the spring is pretty strong.

New dust cover hinges for old Numark tt-100 turntable. It has joint, so it doesn't need nail or screw to work! Big thanks to kalon, for original design which I edited to fit tt100. UPDATE: v2 Added Version 2, with 90 degree angle dust cover...

This is a "perfect" fit hinge for a yamaha p-350 turntable dust cover, robust design, with a stopper at 110 degrees. Hardware Needed: 2x M3X15 bolts per hinge. will screw right into the plastic. ... No "SHU" text in the .stl file

I was having trouble finding a hinge for my turntable so I came up with this design. Print on horizontally for best results and use support. ...Enjoy

The cover has holes in it which makes this construction more sturdy and you can secure it with bars trough the holes, which keep the cover secure. For the bottom part you can easily add a lip to retain the hinge, but I kept it a tight friction fit so...

hinge for technics turntable dust cover work on 1200mk2 1210 1200gr Have fun !

Replacement dust cover hinges for Gemini PT-2100 turntable. Possibly other models aswell. ... Two 3x45mm metal pins required for assembly.

This is a double washer to fix issues with the hinge on the dust cover of Pro-Ject Debut line turntables. The issue is that when the hinge is too tight it will not open properly, and when it is too lose it will start to pull the hinge screws out of...

Outer hinge portion for the dustcover on a Kenwood KD-5033A turntable. You can see the original (broken) hinge parts on the left in my photos and the new printed part. ...Worked great on my cover

this is replacement part for the often broken plastic cover-holder . ... use it with the original metal parts (spring, bolt etc.) strong enough for the original spring.

The first one wasn't quite strong enough, so I made another one.

Reloop torearm rest, based on the technics one. ...It's slightly shorter, based on the 7000MK2 :)