revox a77 tape recorder 3d models

Simple tape dispenser for 6 to 7 rolls of tape.Prints in one piece, face down. Snug supports are recommended on the print bed only.PLA with 0.3 mm layer height. The ø25 mm shaft is intended to be printed in vase mode, with two cylinders fitting into...

A broken tape dispenser spool needs replacement. A suitable alternative has an inner diameter of 75-77mm. The shaft measures 5mm in width and 34.50mm across. Printing the spool horizontally yields best results, using a layer height of 0.3mm or less...

SMT cover tape takeup spool for a drag type feeder - a concept design to replace existing friction feed on current feeder, with final design and print settings to follow after trial runs. For feedback on suitable exotic filaments, I'd appreciate...

I required a holder for a multitude of tapes that I possessed, so I crafted one to consolidate them in one location and affix it to a wall. Now, I have upgraded it (v2) to accommodate large tapes on lower tiers and smaller ones on upper levels. To...

This Kapton tape spreader frame ensures easy application of large expanses of Kapton tape without bubbles or wrinkles. To create it, gather four small or medium clothespins, four thin elastic bands or hair bangles, and four custom-cut 5/16" or 8mm...

This device attaches to the end of a tape measure, enhancing precision when measuring shingled roofs for solar installation professionals like myself who spend hours surveying rooftops daily. The attachment securely friction fits onto the tape...

Place the other end of the tape in the recess given in the base. Then press fit the top onto the base. It clicks in. I have not tried to remove it afterwards. So make sure that you close it after the tape is set correctly. I have uploaded to fit two...

Assembly Time: Take that paper strip (tape measure) and roll it around the bottom structure part one time plus a little extra wiggle room. Now put the band tightener in place, making sure the tape measure goes through the side opening like it's...

Meanwhile, the jagged edge razor integrated into the plastic holder provides an effective method to set the heat, making this device a valuable addition for anyone requiring precise control over their tape dispensing...

additionally supports are no longer needed Post-Printing you will need to cut a small section of a mini hacksaw blade and superglue it to the channel that has been added to the tape gun body. After gluing the blade, superglue the blade cap for...

An adapter to allow the use of braodcast 10 inch tapes on reel to reel tape recorders.

Magnetic tape pulley fixture for Olymp tape recorder/player Recommended one treelike support in centre of hole

You'll also require some 3/16th metal rod, disposable safety-razor blades (similar to those used in pre-1950s safety razors), and a tape spool. Insert the three blades into the 28-toothed wheel, applying a dab of Gorilla Glue on their faces. This...

Now peel off about 8 inches of tape and press fit the roll of tape onto the roll grip. Make sure to fit the side of the tape reel so the backing sits in the channel. Study the assembly drawings. Add the second reel guard and place the dispenser over...

This small keychain can hold about three feet (1m) of duct tape so that whenever something happens, you can be ready. Did the cheap plastic grocery bag start to rip on the way to the car, seconds away from destruction? No worries! You will be...

I broke off the original tape squeegee (third picture) on my packing tape roller years ago, before I owned a 3D-printer. As the roller works fine apart from that, I just lived with it. I had to tape a box recently and as I have had a printer for a...

It is designed for standard 2" (51mm) duct tape. Print instructionsPrint with 100% fan speed, supports (preferably tree supports to save the surface of the base), 0.15 mm layer height, and everything else you normally print with. make sure to block...

Check out my fully automatic feeder here: https://docs.mgrl.de/maschine:pickandplace:feeder:0816feeder Features --- * Designed to be adaptable to your needs through parametric design * The width of one feeder is the tape width plus three millimeters,...

Mounting the tape directly to the wood pole would not work well, so I made this "mount" - the tape sticks to the L-shaped mount which then screws to the post (see photos). The mounts are intended to be used with #8 (M4 metric) finish washer and wood...

See pictures for details. After the piece is bolted into place. Place the end of the tape measure into the curved slot. Then use a small drill to drill out the two small holes. Use two small zip Ties to hold the tape measure AND your cables into...

The measurements vary from tape dispenser to tape dispenser. Please help yourself to fix that with a soldering iron at 150-180 degrees with a separate soldering tip (the tip should not be used for soldering later). :/ sorry for that. ... part list: 5...

To use it, simply return the box until the roll go down and use the wrench to lock the position of the masking tape roll The masking tape roll and the edge of the box will be then perfectly aligned 2 versions are existing One with one bearing (but...

This refillable tape holder comes apart, making it easy to replace rolls of tape. I plan to upload various iterations with alternative cutout patterns. You may want to adjust the printing speed so the teeth come out sharp. I'll experiment with...

Can be used on a belt with a strap (https://www.prisma.film/Arno-Strap-Spannriemen-Bannert-18mm-75cm-schwarz). Each spool type has a 2mm padding on each side so you don't have to touch the tape to hold it, also for better rolling from a belt. This...

For some unknown reason, it's challenging to locate what you're looking for in 25+ rolls of tape? They hang on a 8mm/0.33in diameter copper rod and come in 25mm/1in and 50mm/2in tape versions. Have fun organizing and check out my latest projects on...

I have designed this tape hanger because I have lots of rolls of different types tapes and have a limited space left in my desk drawers, so it came to my mind to design a solution and this is what I came up with, I am using these for a couple of...

An attachment for the Ultimaker, this tape holder snaps onto its sides to keep your tape rolls neat and tidy in the lab. Version 2.0 was released on August 10th, featuring three different sizes with an extra 1mm width to accommodate tape rolls and...

This organizer is designed specifically for manual SMD part placement, serving as a container for taped components and allowing each piece to be easily removed from tape when needed in a given amount. The foil is folded back under the organizer, and...

The "big" shelves are for for tapes with a max diameter of 45mm or less. The "small" shelves are for max diameter 37mm or less. The tube in the middle is always 20mm big. Every shelf has space for 9 15mm tapes. The tube is a pretty tight fit so it...

... It is also feasible to load a combination of roll widths, such as a 2 inch and a 1 inch roll or vice versa. This arm is more than capable of holding a full 1kg spool of filament, ensuring that there is no risk of overloading it with tape rolls.