robo 3d r2

Supplied clip file was too flimsy and warped easily, I made these a little stronger

... keys that come with your R2 and the customizer works great to configure a holder for all your tools . The hex wrench holder is one of the the first prints on my new Robo R2, this printer works great ! PS. ...The holder can work as a handle too.

(In 3ds Max, the Meshsmooth/Turbosmooth function can be used to increase mesh resolution if necessary.) + Real-world scale ( We make 3d model from actual size and images reference. It is best for making video intro, marketing, animation, games... ) +...

Robo R2 - Hotend 24V

https://robo3d.com/products/robo-r2

hotend clamp for the robo R2, made to fit an M3 nut for the clamping bolt instead of being threaded. ... i tested the mounting holes to just thread the bolts through and it seems to hold well

Robo R2 door catch. I used 6mm x 3mm magnets (2 off) and printed this in PETG 0.2 with support from build plate. ... Just slots into the existing holes, just make sure you get your magnets the right way around, I attached mine to the door first...

We designed this spool stand to address the problem of our newest R2 not being compatible with our old generation filament. Our newest filament will be compatible with the R2. ...All of the files are ready to print without supports.

All this model does is raise the R2 printer 30 mm above the platform it is sitting on. ... There are no other benefits by using these feet, unlike the riser feet for the R1 series of printers.

Built in fusion 3d to hold 3 standard DS stylus.

This part fits directly into the vacant hole for the second extruder in the Robo R2, and it helps smooth out the airflow from the tiny fan and around the hexagon extruder heatsink. ...

This is a simple fix to allow an E3D V6 to fit in a Robo R2 3d printer. Requirements are only M3 screws that are 6mm longer than the original ones. This part goes between the stock fan shroud and the carriage. INSTALLATION: 1) Remove fan...

I test new Robo C2, but come to me without holder :) Category: 3D Printer Accessories

I kept losing the thumb nuts off the heat bed of my Robo 3D printer. After searching the internet, (thingiverse in particular), I decided to try to create my own. Used a Caliper to get size. ...It only took two tries to find the right combo.

I test new Robo C2, but come to me without holder :)

Based off of Angrybird12's R2 Guide Instead of running over the top, I'm going to try running along the side.

These two very small parts are added to the mount to address the 10° tilt Robo introduced with the incorrect mounting position of the Raspberry Pi camera. It addresses the error in timelapse video that is tilted 10°. ...Causes the OctoPrint interface...

I did add double sided tape in between the 3D printed parts for extra security and to eliminate any rattling. I also added a small front valance to the model to prevent too much light over-spray (credit to WheresWaldo). The LED lights are 12V...

Allows you to mount a BMG extruder to the standard R2 mount. I printed this in PETG with support at 0.2mm layer height. I used some M3 countersunk 8mm screws to mount it to the carriage. You will also need to adjust your esteps in the eeprom menu...

The individual parts should work with the existing Robo plastic, but are designed to work together. To install the bronze bushings lightly coat a 6mm rod with oil and run it through a bushing so that the epoxy will not stick to the inside of the...

Have you ever seen a Robo R2 3D printing a Robo R2 3D printing a Marvin? Check out our Multi-Color Robo R2 USB Holder! ... Printed with Palette+: http://mosaicmanufacturing.com

Have you ever seen a Robo R2 3D printing a Robo R2 3D printing a Marvin? Check out our Multi-Color Robo R2 USB Holder! ... Printed with Palette+: http://mosaicmanufacturing.com

Have you ever seen a Robo R2 3D printing a Robo R2 3D printing a Marvin? Check out our Multi-Color Robo R2 USB Holder! ... Printed with Palette+: http://mosaicmanufacturing.com

Support axe Z robo R2 en PETG

Replacement fan shroud for the Robo R2 / C2 printer.

A simple clip to go on the door handle of the Robo R2 3d printer and has a spot to keep your stylus. ...   New version added at 12:37 on 1/15/18.

Holder was laid flat on the print bed and turned at a 45 degree angle to fit the Robo R2 print bed.

Clips onto the door handle of a Robo R2 and holds the stylus so I don't loose it. ... Put up a new version at 12:35 on 1/15/18

Replaces the top of the stock Robo R2 / C2 extruder with this adapter to allow direct mounting of the E3D Titan Extruder. ... fixed 2 mm error in Titan placement.

Print 4 of these for aligning Robo R2 and Robo C2 to the gantry. Great for keeping the gantry square when performing maintenance, or realignment from gantry movement. Best way to align and square the gantry on both the C2 and R2 is to loosen the X...