robot chain 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_top_outer_edge_chamfer_radius = .6 stencil_vertical_position = 50 use_mouse_ears = 0 custom_back_camera_x_size = 20...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 0...

After studying what was available, I started modeling my own. The problem was that most of the projects were on console tables, but our table is held on two rails, one on each side. Initially, the project was implemented on a seven-string polispast,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

... with any light color and use a permanent black marker for the text. These models are not designed for dual-color printing. You'll need to print two Monster Ability Card holder v1. ...One is for the Monster cards, the other is for the shop cards.</p>

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

Shroud to complete the FGC-68 do you need to select the Shroud that you like these come in 3 models N (no top rail) TR (with top rail) LR (lower Top RAIL) Link to shrouds FGC-68 Top rail shroud set paintball magfed...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

Larger or smaller screws can be used if you scale the model appropriately, such as M3x8 screws at 150% part scale. Note that buying in bulk from a specialist supplier is significantly cheaper per screw. There are two versions of the container: the...

THIS WILL NOT WORK WITH THE HID GOLIGHT SPOTLIGHTS (GL-3XXXH-X models). If you purchase this transformer with any of our Larson Electronics lights, we will make sure that the connectors are a match.Features: The DCP-25-3XDP 256 watt converter...

Don't use it for rendering or model generation. (see Reducer picture) PRINTING NOTE Print at 100% infill. Try and print standing vertically, if possible so that scaffolding may be ommitted on the inside. These are for sink and drain plumbing only,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.3...

... cut methodology used. All credit for the idea to use them as puzzles goes to Quadratum Cubicum (QuCub.com - no author name noted) and this was already licensed under Creative Commons Attributable before I modeled the pieces and the base/lid. ...

Another thing to note is that there have been a few minor changes to the model since I printed the one in the pic, however I don't think anything changed will cause a problem. The STP file is included for remixing. Just wanted to mention some info...

I probably should make that easier to do if when printing the full model instead of the slices (maybe an exercise for the one wanting to do that - add a better wire hole). I used a 2.1 bluetooth stereo board that I got on ebay for about $21...

On my version, I suggest that you start with 4 seeds in each of the 12 pits (print 4 copies of the 12 seed model and then separate them using nail clippers or small scissors). Increase the number of seeds in each pit progressively to increase the...

Thread the wire through the lower cutout of this model and attach the new wire to the switch by pushing the two quick connectors onto the switch's terminals. ...Press the switch into its place in the case. </p><p>Cover the electronics (<a...

I only own the flat styled one, so that's the one I used to model the part in SW. I think they are both called QuickClick. I believe I may have the older version, &amp; that they've been replaced by the round style (see further down).</p> <p>I can't...

A wrench is used to unscrew the end caps for relamping the fixture, while some competitive models require the “tap and knock off” method to loosen the end cap. 7. Explosion proof, impact and heat resistant Pyrex tubes provide lamp protectionSuperior...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

I already had some Koss Porta Pros so I printed it and used that for a couple of weeks (after tweaking the size of some parts for a tighter fit, especially the push pin which is/was modelled too small). However, after a couple of weeks using that,...

the better the less likely it will grab but u can always use nuts on the other side even tho i didnt make a place for them to sit on the model since i had planned on using the threaded inserts but it will still work cause thats how i test fit...

The hole for the cable tip should be wide enough for any similar cables, but if not you can pretty easily remix the model by just cutting the hole to be larger or adding material where needed. I suggest printing the dock upside down and including...

... most of these parts. If there are any tweaks necessary let me know. I have added a .step file of the assembled printer and I will upload a Fusion 360 back up file as soon as its processed so you guys can go nuts customizing the solid models.

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_corner_resolution = 8 custom_right_port_corner_radius = 5 custom_back_camera_x_position = 0...

Some of the models are difficult to hand-launched and should be tested with a 1/16" rubber band instead. A slight elevator-up reflex is required for flight. This is accomplished by latching the elevons up on the relex tabs on the aft end of the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 0 stencil_size = 40 stencil_shape = 1 stencil_mirror = 0 custom_back_extra_port_x_size = 30...