rollerblade inline skates 3d models

Rules for participation are as follows: Submissions must be printable on a MakerBot; bearings of any size or style (such as skate bearings readily available at sports stores with dimensions 8mm ID, 22mm OD, and 7mm thickness) must be incorporated in...

For your convenience, I've uploaded all parts required for the Z-axis assembly, including designs for a pulley and skate bearing brackets that fit onto corner brackets. ...These assemblies are designed to work efficiently with tapered M3 bolts, which...

Box Charkha parts: •2 sheets total 12”x12”x¼” plywood •1 sheet total 12”x20” 1/8” plywood •2 ABEC-9 skate bearings (center hole has to fit on a 5/16" bolt) •2 5/16 hex head by 1 3/4” bolts to use as a post for the wheels (need an unthreaded section,...

It is intended to use a standard 60822 bearing, as found on skates and skateboards, and fit onto the standard side mounted retractable arm with the twist locking end. Two versions are included: * spool-1-* is a 2 piece design where you can use...

A 608 "skate" bearing serves as one side of the pinch, while when two extruders face each other, the stepper shaft is coated with rough material and epoxy (the "No Epoxy" refers to no PTFE being epoxied in place). The design can be rebuilt under...

You need two 608 skate bearings, and two 8mm x 35-40mm bolts and nuts. This version will surface mount with 4 sheetrock or better screws. There are two wheel designs one fancy and one easier to print. I find that the wheels print well in the...

You need two 608 skate bearings, and two 8mm x 35-40mm bolts and nuts. You can either tie a line to the top or use a carabiner as a clip. There are two wheel designs one fancy and one easier to print. I find that the wheels print well in the...

Eva / Evavoo - https://www.instagram.com/evavoo_art/Russell Taysom - https://www.instagram.com/russelltaysom/ Bringing you serious low brow, skate art, gloopy goodness, the design prints with no need for support, and has an integrated fitting on the...

I used 2 skate bearings pressed into the handle body using a bench vise. The crank handle was also printed horizontally on a raft at 20%. It may print fine vertically though, but I though it might be stronger if printed horizontally. This...

Required parts include a high-torque stepper motor (e.g., from Anaheim Automation), four M3x10 bolts for motor mounting, a 20mL syringe with a 20mm OD, an M8 ID 26mm OD "skate" bearing, a large 5mm ID 16mm OD GT2 pulley, 300mm of GT2 belt, an M4x15...

* One skate-board / surf-board-like shape for the technical parts : 2 batteries are under the traveler space, and one electric motor on each rear wheel. The wheel are covered to protect them from the little accidents we have in an urban environment...

This stylish ride is built to withstand urban assault courses and skate parks worldwide. The Glide Master boasts unique features like a BMX-inspired front end with 1.5 inches of suspension, a V-brake for maximum stopping power, and removable foot...

I envisioned an "open-source" motor design that could be easily constructed using a 3D printer, magnet wire, and standard components such as skate bearings. To achieve this, I developed a parametric OpenSCAD script for creating the coil forms and...

... either to solder them or to keep them fixed. It has a small handle which moves a pulley with an off-center center, that way the skates are braked. ...For the rotational movement it is necessary to add two 608zz bearings which enter under pressure.

Wax up and skate! Extra steps: (Not a necessity but will make it look/hold together better) 9. Give 2 coats of clear lacquer and leave to set. Alternately you can paint it with a coat of watered down PVA. *you can use thinned down Vaseline as...

Eu usei rolamentos velhos que o meu filho tirou do Skate dele. Imprima uma peças de cada, porém a arruela do carretel tem que imprimir duas. 10% de infil em tudo exceto no pino que é melhor colocar 30% pois é a única peça que sofre esforço e como é...

... You can then use a much lower current for the Y-motor or also replace it with a NEMA17. For the whole Z-axis assembly, I've now got everything uploaded. I made parts to make a pulley, skate bearing brackets to fit onto the corner brackets.

It will allow you to use common 608 skate bearings. This obsoletes the Z-Studding tie bracket, which require more material than this object, but needs no bearing (does need an M5 bolt and two nuts). For other bearings, simply adjust "bearing_OD" and...

I used standard skate bearings with a ID of 8mm and OD of 22mm (I froze the bearings to help insert them in the shaft.) This design supports my 1kg and 500g rolls. I downloaded an M8 nut off of Thingiverse although I don't think it is necessary for...

2 skate bearings (has to fit on a 5/16" bolt) The number on mine is ABEC-9. OD is about 22mm 2 each 5/16 hex head bolts to use as a post for the wheels. These should have a section that has no threads. They will be cut down...

Eva / Evavoo - https://www.instagram.com/evavoo_art/ Russell Taysom - https://www.instagram.com/russelltaysom/ Bringing you serious low brow, skate art, gloopy goodness, the design prints with no need for support, and has an integrated fitting on...

NEW VERSION HERE: http://www.thingiverse.com/thing:1070481 This spool holder is using 4 standard 608zz roller/skate ball bearings to limit friction. Print two supports then insert the bearings onto the pegs. They are designed to hold firmly the...

It requires a single skate board bearing that snap fits into the center of the roller and then snap fits onto the stem of the mount. Once or twice I had a really tightly wound filament or the end of a roll work its way off the roller so I design a...

Inspired by http://garyhodgson.com/reprap/wp-content/uploads/2012/01/Prusa-Mendel-Off-Carriage-Extruder-PoC-MattRobertsCompactExtruder.png, this design requires a 608 skate bearing and Vex Robotics square shaft (12 inches), along with printed parts...

I used Skate bearings but took them out as they made no difference in functionality. Simple is best! I printed at 0.2mm but I would print them at 0.3mm per layer if I had to do it all over again. The Gcode is for 0.2mm using a 0.4mm nozzle. I...

This high-quality fantasy model, titled "Cartoon_Skate_Girl_Rigged," offers various file formats such as Maya 2014 (with Arnold 1.2.4), Maya 2018 (with Arnold 2.0), FBX, and OBJ. It features a clean topology based on quads with clear node naming,...

The holder requires printing 2 brackets and includes necessary parts like M8 bolts/screws, M8 washers, M8 nuts, skate bearings, and M5 screws with T-nuts. Designed specifically for the Mendelmax 2.0, it might also fit other 3D printers using 20x20mm...

130mm in length - Depending on the above 1 or 2 M8 lock nuts - Two M8 washers - Two 608 'skate' bearings See the exploded view for a detailed image of how to assemble. You can optionally print and use the nut driver for the assembly, it will fit...

Constructed from birch and MDF, this collection boasts finished edges with skated brush details. The dimensions are 220 cm high, 200 cm wide, and 50 cm deep, weighing 0.1 kg. The price is €399.00, and it has 11,210 polygons. Textures can be found...

I have modded these X-ends to suit the Thompson SPM08 linear bearings (slide like smooth buttery goodness.) I have included the 608 skate bearing cheek mod, and have also fixed a recently detected issue with the "Friction Fit" on 8mm smooth rod (the...